MECHANICAL HANGING SOLUTIONS

Express

XP2 NO 2 LOOP HANGERS W/EXPRESS FASTENER
The fastest locking device solution for fast suspension of a variety of services.
XP2-LG-5FT 10 per bag
XP2-LG-10FT 10 per bag
XP2-LG-15FT 10 per bag
XP2-LG-20FT 10 per bag
XP2-LG-30FT 10 per bag

Dyna-Tite

Zip-Clip Lock with 3in Looped Cable Kit
  • Kits feature one (ZC) or two (DZC) Zip-Clips and Looped Cable,
  • Fits inside unistrut and are ideal for multi-tiered applications,
  • Cable lock combined with wire rope is a more efficient method,
  • Spring loaded pawl which allows entry and passage of wire rope through the lock,
  • Wire rope is gripped with increasing pressure as the suspended load is increased,
  • Lock has an integrated release to disengage the gripping pawl,
  • Suitable for use with single or multitiered trapeze systems and in applications supporting such items as rectangular ductwork, cable trays, baskets, etc
  • ...
ZCWR5 10pk
ZCWR10 10pk
ZCWR15 10pk
ZCWR25 5pk
DZCWR5 10pk
DZCWR10 10pk
DZCWR15 10pk
DZCWR25 5pk
Dyna-Stud Cable Assembly
Dyna-Studs used with Dyna-Tite cable locks can greatly decrease labor time for constructing suspension systems from a concrete or steel structure.
DSA1405-332 (10 pk)
DSA1410-332 (10 pk)
DSA1415-332 (10 pk)
DSA1425-332 (5 pk)
DSA3805-18 (10 pk)
DSA3810-18 (10 pk)
DSA3815-18 (10 pk)
DSA3825-18 (5 pk)
DSA3805ZC (10 pk)
DSA3810ZC (10 pk)
DSA3815ZC (10 pk)
DSA3825ZC (5 pk)
Wire Rope with 45, 90 Degree or Straight Eyelet
Duro Dyne Dyna-Tite eyelets are manufactured of zinc plated cold rolled steel and swaged to the wire rope cable with a hydraulic press.
1/4 inch
3/8 inch
Straight only available in 3/32 cable and 1/4 hole
45 degree
90 degree
1/8 x 5ft 10pk
1/8 x 10ft 10pk
1/8 x 15ft 10pk
1/8 x 25ft 5pk
3/32 x 5ft 10pk
3/32 x 10ft 10pk
3/32 x 15ft 10pk
3/32 x 25ft 5pk
LC12K Looped Cable with CL12 Cable Lock
  • Duro Loop Cable Sling enhances the Dyna-Tite suspension system by the addition of a pre-looped cable end
  • Wire rope is pulled around the anchor point and through the looped end of the cable, it is already secured at one end, saving time at the jobsite
  • Remaining wire rope “drop” is passed through a channel in the Dyna-Tite Cable Lock
  • Wire rope is either wrapped around the ductwork or inserted through a fastening point and back up into the second channel of the same cable lock
  • Locking teeth inside the cable lock engage the wire rope which secures the ductwork in place
  • To ensure maximum safety, use only looped wire rope supplied by Duro Dyne with all cable lock applications
  • ...
30134 30ft 3in loop 5bg
30185 5ft 3/32 3in loop 10bg
30186 10ft 3/32 3in loop 10bg
30187 15ft 3/32 3in loop 10bg
WC Wire Rope Spool
Aviation grade galvanized wire rope supplied by Duro Dyne is manufactured to exacting standards and statistically tested to verify stated breaking strengths.
30200 WC2-CL6 7x7 Strand 500ft
30202 WC3-CL12 7x7 Strand 500ft
30204 WC4-CL18 7x7 Strand 500ft
30206 WC6-CL23 7x19 Strand 250ft
30208 WC8-CL25 7x19 Strand 250ft
DCS25 Duct Cable Flexible Saddle 25ft Roll
Dyna-Tite Cable saddle is used to protect spiral or rectangular ductwork from the abrasions of cable.
LC Looped Cable
  • Duro Loop Cable Sling enhances the Dyna-Tite suspension system by the addition of a pre-looped cable end
  • Once the wire rope is pulled around the anchor point and through the looped end of the cable, it is already secured at one end, saving time at the jobsite
  • The remaining wire rope “drop” is passed through a channel in the Dyna-Tite Cable Lock
  • Then, the wire rope is either wrapped around the ductwork or inserted through a fastening point and back up into the second channel of the same cable lock
  • The locking teeth inside the cable lock engage the wire rope which secures the ductwork in place
  • To ensure maximum safety, use only looped wire rope supplied by Duro Dyne with all cable lock applications
  • ...
30228 5ft 3/32 1-1/2in loop 10bg
30229 10ft 3/32 1-1/2in loop 10bg
30230 15ft 3/32 1-1/2in loop 10bg
30232 25ft 3/32 1-1/2in loop 5bg
30233 5ft 1/8 3in loop 10bg
30234 10ft 1/8 3in loop 10bg
30235 15ft 1/8 3in loop 10bg
30237 25ft 1/8 3in loop 5bg
DSB1 Dyna-Tite Spiral Buckle (50 box)
  • This zinc plated 14 gauge buckle is designed to suspend round and oval ductwork from ceiling joists or beams with the use of threaded rod up to 3/8” in diameter
  • Simply place 1” hanging strap in one side of the buckle then around the material and into the other side of the buckle
  • When the strap is correctly inserted through the slots, the strap is locked into the buckle by the weight of the duct
  • ...
CL Dynatite Cable Lock (box of 10)
  • CL6, CL12, CL18 and CL23 have all been SMACNA approved for Seismic Applications
  • All locks feature an easy release pin
  • The Maximum Load Range for each size wire rope incorporates a design safety factor of 5:1, The CL23 and wire rope combination should be sized for the job so that the projected load falls within the appropriate working load limit (WLL)
  • The CL18 Cable Lock is for use with 3/32 inch and 1/8 wire rope, depending upon the wire rope utilized, the CL18 has a working load limit of up to 225 lbs
  • The CL12 is designed for use with 3/32 inch wire rope ONLY, the CL12 is the perfect product for hanging smaller diameter spiral (less than 24 inches), typical residential and light commercial ductwork, and air handlers in attics
  • ...
30348 CL6-WC2 use w/WC2-CL6 Wire
30350 CL23-WC6 use w/WC6-CL23 Wire
30351 CL12-WC2 use w/WC3-CL12 Wire
30354 CL18-WC4 use w/WC4-CL18 Wire
KV12 Bracket Assembly w/CL12
  • KV bracket assembly enhances the Dyna-Tite suspension system by the addition of an integral bracket, which fastens the cable lock to the duct with sheet metal screws
  • Once the KV assembly bracket is attached to the duct, the wire rope “drop” is passed into the entry hole at the top of the bracket, through the cable lock, and out the exit hole at the bottom
  • The locking teeth inside the cable lock engage the wire rope and secure the ductwork in place
  • ...
CCC1 Custom Cable Counter w/ Lid
The CCC1 makes preparing for your duct hanging project alot simpler; take an empty five gallon bucket, put a spool of wire rope in the bottom, put in some boxes of Dynatite cable locks and a cable cutter; place the CCC1 on top of the bucket and you are ready for the jobsite, thread the wire rope through the measuring device and you are ready to hang ductwork, just pull the wire rope to the length ...
DTWRC Cable Cutter
  • Safety Catch
  • 3/16” Cutting Capacity
  • Spring Loaded For Ease Of Use
  • 5” Long Handles For High Leverage
  • Hardened Steel Blades For Durability
  • Vinyl Coated Handles For Comfortable, Non-Slip Grip

SHEET METAL ACCESSORY PRODUCTS

DuroZone

CODR XCODR Round Cable Operated Damper
CODR Internal Cable Mount XCODR External Cable Mount Installation of a cable operated balancing damper allows the balancing contractor a convenient way to adjust air volume without entering the ceiling space.
Internal
External
3 FT
5 FT
8 FT
10 FT
15 FT
4 inch
5 inch
6 inch
7 inch
8 inch
9 inch
10 inch
12 inch
14 inch
16 inch
18 inch
20 inch
22 inch
24 inch
CODS XCODS Rectangle Cable Operated Damper
CODS Internal Cable Mount XCODS External Cable Mount Installation of a cable operated balancing damper allows the balancing contractor a convenient way to adjust air volume without entering the ceiling space.
6x6
8x6
10x6
12x6
14x6
16x6
18x6
20x6
22x6
24x6
8x8
10x8
12x8
14x8
16x8
18x8
20x8
22x8
24x8
10x10
12x10
14x10
16x10
18x10
20x10
22x10
24x10
12x12
14x12
16x12
18x12
20x12
22x12
24x12
14x14
16x14
18x14
20x14
22x14
24x14
16x16
18x16
20x16
22x16
24x16
18x18
20x18
22x18
24x18
20x20
22x20
24x20
22x22
24x22
24x24
Internal
External
3 FT
5 FT
8 FT
10 FT
15 FT
DD DDRD Pressure Relief Damper
Rectangular Pressure Relief Dampers (DD Series) DuroZone Pressure Relief Dampers are used to relieve duct systems of pressure build up created as zones are satisfied and zone dampers travel to a closed position.
8 inch
10 inch
12 inch
14 inch
16 inch
12x8 inch
18x8 inch
20x10 inch
20x12 inch
DuroZone Replacement Motors
DuroZone has a wide variety of replacement motors for all the dampers it manufactures.
35092 RMWCRD
35093 RMCD
35105 MSSR024
35107 RMMP13
35109 RMMP34
35138 RM-RD/MS
35139 RM-MB
35141 RMSR024
35142 RMSR110
37208 SRHTM024
37209 SRHTM110
MS Multi-Size Damper
6x12 inch
6x20 inch
8x16 inch
8x16 inch
10x16 inch
10x24 inch
12x16 inch
12x24 inch
NSPRD024 Spring Return Round Damper 24 volt
4 inch
5 inch
6 inch
7 inch
8 inch
9 inch
10 inch
11 inch
12 inch
14 inch
16 inch
18 inch
RD Round Zone Damper
  • Housing and blade made of galvanized steel with reinforced beads for maximum durability
  • High-Torque Motor will work with all existing 24-volt thermostats
  • High-torque means reliable, trouble-free service for many years
  • Low-Leakage, Single-Blade Design insures smooth operation and efficient sealing for maximum control of air flow
  • Damper attaches to duct by use of nylon ties or screws, easy wiring, no screwdriver required
  • Designed for use with flexible ducting or round duct
  • Damper motor guaranteed for three years after installation
  • ...
4 inch
5 inch
6 inch
7 inch
8 inch
9 inch
10 inch
11 inch
12 inch
13 inch
14 inch
16 inch
18 inch
RRD6 RRDS6 Retrofit Round Damper
35100 PO/PC 6in
35101 SO/PC 6in
SPMS Spring Return Multi-Size Damper (SC - Spring Closed, SO - Spring Open) 24 volt
Description Duct Height Min Width Max Width
  • 37000 612SC* 24 Volt Spring Closed Multi-Size Damper 6 8 12
  • 37001 620SC 24 Volt Spring Closed Multi-Size Damper 6 14 20
  • 37002 816SC 24 Volt Spring Closed Multi-Size Damper 8 10 16
  • 37003 824SC 24 Volt Spring Closed Multi-Size Damper 8 18 24
  • 37004 1016SC 24 Volt Spring Closed Multi-Size Damper 10 10 16
  • 37005 612SO* 24 Volt Spring Open Multi-Size Damper 6 8 12
  • 37006 620SO 24 Volt Spring Open Multi-Size Damper 6 14 20
  • 37007 816SO 24 Volt Spring Open Multi-Size Damper 8 10 16
  • 37008 824SO 24 Volt Spring Open Multi-Size Damper 8 18 24
  • 37009 1016SO 24 Volt Spring Open Multi-Size Damper 10 10 16
  • 37086 1024SO 24 Volt Spring Open Multi-Size Damper 10 18 24
  • 37087 1216SO 24 Volt Spring Open Multi-Size Damper 12 12 16
  • 37088 1224SO 24 Volt Spring Open Multi-Size Damper 12 18 24
  • 37096 1416SO 24 Volt Spring Open Multi-Size Damper 14 12 16
  • 37097 1424SO 24 Volt Spring Open Multi-Size Damper 14 18 24
  • ...
37000 SC 6x12
37001 SC 6x20
37002 SC 8x16
37003 SC 8x24
37004 SC 10x16
37005 SO 6x12
37006 SO 6x20
37007 SO 8x16
37008 SO 8x24
37009 SO 10x16
37086 SO 10x24
37087 SO 12x16
37088 SO 12x24
37096 SO 14x16
SRHT024 Hi-Torque Spring Return Round Damper
10 inch
12 inch
14 inch
16 inch
18 inch
20 inch
Thermostat Wire on Reel
General Purpose 18GA wire on reel
2 wire 500ft
3 wire 500ft
4 wire 250ft
5 wire 250ft
6 wire 250ft
8 wire 250ft
RED4N Zone System Panel Kit
The RED4 microprocessor zone control panel is suitable for all 2,3 and 4 zone applications.
RCD Diffuser Damper
The RCD damper is a variable position damper that is controlled by an OSL Occupancy Sensor or the MWC Manual Wall Control.
6 inch
7 inch
8 inch
9 inch
10 inch
12 inch
SMZ JTZ and RED Control Pannels
SMZ Panels DuroZone’s SMZ-SW Panels provide contractors with a simple, low-cost zoning system for 2, 3, or 4 zones.
35226 SMZ2SW 2 Zone
35227 SMZ3SW 3 Zone
35228 SMZ4SW 4 Zone
35229 SMZAC 3 Zone Autochange
35234 RED4 4 Zone Electronic Digital
35235 JTZHP 3 Zone Heat Pump
SMZ JTZ Duro Zone System Packages
JTZ and SMZ Zone Control Packages provide, in one convenient box, all the controls necessary to install a 2 or 3 zone system.
35029 J2HSP JTZ2 Zone Heat Pump
35030 J2HSP JTZ 3 Zone Heat Pump
35260 S2P SMZ 2 Zone
35261 S3P SMZ 3 Zone
35262 S2SP SMZ 2 Zone Setback
35263 S3SP SMZ 3 Zone Setback
35269 S4P SMZ 4 Zone
35270 S4SP SMZ 4 Zone Setback
35271 S2AP SMZAC 2 Zone
35272 S3AP SMZAC 3 Zone
35273 S2ASP SMZAC 2 Zone Setback
35274 S3ASP SMZAC 3 Zone setback
PMB Power Open/Power Closed (OBD) Damper
Refer to chart image for A B C D E price code by size The DuroZone Multi-Blade damper for residential zoning systems has been engineered to include many features, The new opposed blade design with heavy neoprene blend on top and bottom ensures a tight rattle free seal, They are ribbed for strength and extruded from lightweight aluminum, The sleek frame profile provides maximum strength without exc...
A
B
C
D
E
37230 8x6
37231 10x6
37233 12x6
37234 14x6
37240 6x8
37241 8x8
37242 10x8
37250 6x10
37251 8x10
37260 6x12
37270 6x16
37235 16x6
37236 18x6
37243 12x8
37244 14x8
37245 16x8
37252 10x10
37253 12x10
37261 8x12
37262 10x12
37271 8x14
37280 6X16
37281 8X16
37290 6X18
37300 6X20
37237 20x6
37238 22x6
37239 24x6
37246 18x8
37247 20x8
37254 14x10
37255 16x10
37263 12x12
37264 14x12
37272 10x14
37273 12x14
37282 10x16
37291 8x18
37301 8x20
37310 6x22
37320 6x24
37248 22x8
37248 22x8
37249 24x8
37256 18x10
37257 20x10
37258 22x10
37265 16x12
37266 18x12
37274 14x14
37275 16x14
37283 12x16
37284 14x16
37292 10x18
37293 12x18
37302 10x20
37311 8x22
37312 10x22
37321 8x24
37259 24x10
37267 20x12
37268 22x12
37269 24x12
37276 18x14
37277 20x14
37285 16x16
37286 18x16
37287 20x16
37294 14x18
37295 16x18
37303 12x20
37304 14x20
37313 12x22
37322 10x24
37323 12x24
SMB Spring Return High-Torque Multi-Blade Damper
Refer to chart on product's web page to select Model #, Size and Option Price Category Code.
A
B
C
D
E
MMB Spring Open Return Mid-Torque Multi-Blade Damper
Refer to chart on product's web page to select Model #, Size and Option Price Category Code.
A
B
C
D
E

4 Bolt Connection Systems & Ductwork Accessories

QSD 10x6 Quick Snap Insulated Access Door
  • One door fits all sizes of spiral duct from 10” diameter and up
  • Proprietary foam gasket ensures a tight seal
  • Quick snap fasteners for fast installation and removal
  • Stainless Steel construction for corrosion resistance
  • One piece door design for easy alignment in duct opening
  • QSD doors are designed and tested for positive static pressure applications
  • Green Product! The QSD has 60% less steel content than standard two piece access doors
  • ...
MRAD Insulated/Uninsulated Access Door (for Round Pipe)
  • INSULATED MRADI / UNINSULATED MRADU
  • ▪ Available in 4x8 for 7'', 11'' and 14'' round duct
  • ▪ Available in 8x12 for 14'', 18'' and 22'' round duct
  • ▪ Available in 12x16 for 18'' and 24'' round duct
21101 MRADU 4x8-7
21103 MRADU 4x8-11
21104 MRADU 4x8-14
21110 MRADU 8x12-14
21112 MRADU 8x12-18
21114 MRADU 8x12-22
21117 MRADU 12x16-18
21120 MRADU 12x16-24
21135 MRADI 4x8-7
21137 MRADI 4x8-11
21138 MRADI 4x8-14
21144 MRADI 8x12-14
21146 MRADI 8x12-18
21148 MRADI 8x12-22
21151 MRADI 12x16-18
21154 MRADI 12x16-24
MFAD Insulated/Unisilated Access Door (for Rectangular Duct
  • INSULATED MFADI - Available in 4x8; 8x12 and 12x16
  • UNINSULATED MFADU - Available in 4x8; 8x12 and 12x16
21170 MFADU 4x8
21171 MFADU 8x12
21172 MFADU 12x16
21177 MFADI 4x8
21178 MFADI 8x12
21179 MFADI 12x16
MHTAD High Temperature Access Door (2000 degree)
  • Uninsulated, flat high temp doors
  • Available in 8x4, 12x8, and 16x12
  • Available with or without plate
21190 8x4
21191 12x8
21192 16x12
21195 8x4 w/Plate
21196 12x8 w/Plate
21197 16x12 w/Plate
HTV Turning Vane 10ft
  • 2in Turning Vane is manufactured from 26-gauge galvanized steel
  • 4in Turning Vane is manufactured from 24-gauge galvanized steel
13207 4in 24ga
13203 2in 26ga
SS Standing S Lock
  • Designed to reinforce the connection on the wider ductwork applications
  • Available in 10ft lengths
13228 1/2in x 10ft 26ga
13214 1in x 10ft 24ga
FD Flat Drive Cleat
  • Designed to secure the connection for lighter ductwork applications
  • Perfect for lighter gauge and residential ductwork applications
  • Tapered ends for an easy start
  • Available in 5ft or 10ft lengths
13218 1in x 5ft 26ga
13255 1in x 10ft 24ga
FS Flat S Lock
  • Designed to secure the connection for lighter ductwork applications
  • Available in 5ft or 10ft lengths
13256 1in x 10ft 24ga
13219 1in x 5ft 26ga
DHVR 22ga Dyn-O-Mate Rail 10ft
  • The Vane Rail has self aligning tabs for easy vane installation
  • 2in and 4in Vane Rail is manufactured from 24 or 22-gauge galvanized steel
13300 2in
13302 4in
RLT Dyn-O-Loc Tool
  • Tie rods can be used to support duct sizes over 48"
  • Dyn-O-Locs insert into the ends of the hollow tie rods to provide a means of attaching the rods to the duct
  • Available for use in 1/2" and 3/4" ID rods they are easily inserted and and have been pull tested to withstand over 1900 lbs
DOMRL Dyn-O-Loc (250 box)
  • Tie rods can be used to support duct sizes over 48"
  • Dyn-O-Locs insert into the ends of the hollow tie rods to provide a means of attaching the rods to the duct
  • Available for use in 1/2" and 3/4" ID rods, they are easily inserted and and have been pull tested to withstand over 1900 lbs
21097 1/2in
21098 3/4in
DOMJ J Flange 100
  • Designed to strengthen the duct wall and connect duct sections together
  • Furnished with an integrated sealant pocket for a secure air tight fit
  • Manufactured from 20-gauge steel in 10ft, 12ft & 20ft lengths
  • DOMJ is designed for large commercial and high-pressure applications
DDJ Corner for DOMJ Flange
DDJ corners are manufactured from 11-gauge steel, for use with DOMJ Flange.
DDCS TDC Stackable Corner
  • DDCS (TDC) corners are for use in corner insertion machines and are manufactured from 16-gauge steel
  • Also available in Aluminum and Stainless Steel
DOMCLT 6in Metal Cleat 20 Gauge (Box of 500)
  • DOM-CLT and DOM-PCLT for use with DOMJ & DOMH 20 gauge flanges for airtight duct connections
  • DOM-CLT and TDF-CLT are manufactured from 20 gauge galvanized steel 6” pieces
  • DOM-PCLT AND TDF-PCLT are extruded 7/100” PVC and designed for breakaway connection needs
DOMC TDC Corner
TDC & TDF Stackable Corners are for use in corner insertion machines and are manufactured from 16-gauge steel.
DOMF TDF Corner
TDC & TDF Stackable Corners are for use in corner insertion machines and are manufactured from 16-gauge steel.
Quad Cleats 6in (250 ft box, 500 clips)
  • Compatible with Dyn-O-Mate™ J, Ductmate™ 35, CL Ward™ J, Ward Industries™ J, Hardcast™ flanges, TDC, TDF and TDX Connections
  • Manufactured from 22 gauge galvanized steel
21259 DOMQCLT
21269 HDQC-PLUS
DDEJ 16ga Quad Corner
  • Dyn-O-Mate Quad Corner is a versatile corner for use in Dyn-O-Mate J as well as many other flanges
  • Unique design of this corner results in performance like that expected from heavier gage, but at a lower cost
  • Compatible with Dyn-O-Mate™ J Ductmate™ 35, CL Ward™ J Ward Industries™ J and Hardcast flanges
  • Quad corners are manufactured from 16-gauge steel
  • ...
Quick Corner for Ward Flange J
CNR J — J Flange Corner
DA200 Duct Protection Wrap / Film - 3 mil - 200ft Roll
  • Polyethylene film coated with an aggressive adhesive designed to prevent outside debris from contaminating ductwork prior to the to jobsite installation
  • Excellent surface protection film that is widely used in the construction industry to protect flooring and other surfaces from damage
  • 3 mil blue - adhesive inside or out, others colors available
  • Minimum elongation 600%
  • Minimum tensile strength 15-4/10 lbs/in
  • ...
24in Blue
36in Blue
48in Blue
60in Blue
24in Reverse Blue
36in Reverse Blue
Wire Mesh
Wire Mesh from Duro Dyne is ideal for protecting your ductwork from rodents, animals and large debris.
BN316-34 3/16x3/4 Neoprene Gasket (Box of 20 rolls - 50ft each)
  • Neoprene gasket tape is a self-adhesive closed cell industrial foam comprised of neoprene, PVC and Nitrile
  • Great for use when connecting ductwork that might periodically have to be taken apart for maintenance purposes
  • Color: Black
  • Temperature range: -40°F to 200°F
  • Good chemical resistance
BTL500 Butyl Gasketing 25ft Roll
Duro Dyne BTL500 is a UL Classified permanently soft caulking compound designed for sealing flanged joints in duct systems; It adheres to clean dry metal surfaces and does not promote corrosion.
NEO750 Neoprene Gasketing 50ft Roll
Duro Dyne Neoprene gasket tape is a self-adhesive closed cell, neoprene blend elastomeric foam; It is great for use when connecting ductwork that might periodically have to be taken apart for maintenance purposes.
Cleat Tool
  • Install the finishing cleat quickly and easily
  • The tool pulls the ductwork tight while installing the cleat and creating a quick, easy and clean seal on duct connections over 48''
21051 DCTDOM deluxe
21070 DOMCT regular
DOMCRMP TDC/TDF Crimper Tool
The Dyn-O-Mate Crimper installs the TDC or TDF corner and crimps the edge over to hold the corner in place.

Flexible Duct Connector / Vane Rail

EBX-100 Econofab Excelon Duct Connector
  • 2-3/4in Metal, 4in Fabric Black Excelon, 2-3/4in Metal; 28 GA Galvanized, Guard Loc Seam
  • For light commercial or larger residential systems
MBX4-100 3x3x3 Metalfab Duct Connector Excelon
  • 3in Metal, 3in Fabric Black Excelon, 3in Metal; 24 GA Galvanized, Grip Loc Seam
  • Metal-Fab is constructed of material which meets the requirements of heavy commercial systems
  • This factory fabricated flexible duct connection will allow for normal vibration in large duct systems without inhibiting the effectiveness of the flexible duct connector
MBX4x4x4-100 TDC/TDF Excelon Duct Connector
  • 4in Metal, 4in Fabric Black Excelon, 4in Metal; 24 GA Galvanized, Grip Loc Seam
  • TDC/TDF Connector has ample material for roll forming a connecting flange on both sides of the flexible connection
  • This product is designed to be compatible with both TDC (Lockformer) and TDF (Engel) roll forming flange-fabricating equipment
MFN4-100 Metalfab Neoprene Duct Connector
  • 3in Metal, 3in Fabric Neoprene, 3in Metal; 24 GA Galvanized, Grip Loc Seam
  • Metal-Fab is constructed of material which meets the requirements of heavy commercial systems
  • This factory fabricated flexible duct connection will allow for normal vibration in large duct systems without inhibiting the effectiveness of the flexible duct connector
MFN4x4x4-100 TDC/TDF Neoprene Duct Connector
  • 4in Metal, 4in Fabric Neoprene, 4in Metal; 24 GA Galvanized, Grip Loc Seam
  • TDC/TDF Connector has ample material for roll forming a connecting flange on both sides of the flexible connection
  • This product is designed to be compatible with both TDC (Lockformer) and TDF (Engel) roll forming flange-fabricating equipment
FFF Metal Fab Excelon Duct Connector
All Metal-Fab, Super Metal-Fab and TDC/TDF Flexible Duct Connectors are manufactured with 24 gauge galvanized steel.
10266 3x3x3 orange box
10267 4x4x4 red box
SMBX4-100 3x3x3 Single Fold Black Excelon Duct Connector
  • 24 GA Galvanized
  • Single Fold Seam
  • Black Exceleon
JBXME Junior Duct Connector Excelon ME
  • Black Excelon ME
  • Continuous Temp Range -40° to 180° F
  • Base Fabric Woven Ployester
  • Coating Vinyl
  • Weight Per Square Yard 16 oz
  • Leakage Resistance 1 350 psi
  • Tear Strength 2 100/100 lbs
  • Tensile Strength 3 240/220 lbs
SMBX4x4x4-100 Single Fold Black Excelon Duct Connector
  • 24 GA Galvanized
  • Single Fold Seam
  • Black Excelon
VR2 Duro Vane Rail
  • Air travelling throughout a duct is slowed up when it reaches a right turn angle, this is detrimental to the efficiency of the duct system
  • Air turning vane assemblies are used to guide air evenly around such turns
  • Duro Vane Rail, which is a pre-fab side rail, layout time is eliminated.
Duro Stapler and Staples
Duro Dyne's Flexible Connector fabric seam can be quickly closed using the handy Duro Stapler.
10065 HS-1 Rapid-31 Stapler
10059 DSP1 Staples (Box of 5,000)

Air Regulation Control

Rapit® Bearings and Accessories
The RAPIT is an inexpensive, rattle-free regulator for quick installation on balance or splitter dampers.
7190 RP3-50NEO Washer (100 pack)
8088 RB50 Spring Bearing (100 pack)
8089 RP1 Handle for RB50 / ES14 (100 pack)
8090 RP2 5/16-18 Wing Nut (100 pack)
8091 RP3 5/16 Washer (100 pack)
8201 RB25T Threaded Bearing (100 pack)
Specline® Damper Regulators
Specline Regulators are designed for minimum leakage applications.
8012 SRH280 3/8 Indicator Style Hex Nut
8013 SRH288 3/8 Cast Handle Hex Nut
8023 SRS338 3/8 Acorn Nut
8027 SB138 3/8 Open End Bearing (25pk)
8028 SB338 3/8 Closed End Bearing
8033 SRP516 Ball Joint
KP20 3/8in Damper Casting
Damper And Deflector Castings control 3/8” round rod where rod is used to operate dampers.
KP25 3/8in Damper Rod Clip (Box of 100)
KR3 3/8in Dial Regulator for Square Rod
The 3/8” bearings and regulator are suitable to use on round as well as square duct.
KS12 1/2in Quadrant Set for Dampers to 30in
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of the damper, The frame is marked to show the exact position of the damper, For use on square or round ducts Consists of -
  • K-5 quadrant
  • KP-10R round end bearing
  • KP-10S square end bearing
K2 1/4in Dial Regulator for Square Rod
These heavy gauge plated steel regulators are among the most popular on the market.
K4 3/8in Quadrant for Square Rod
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of the damper.
KP End Bearings
8064 KL7R 1/2" Round Long
8065 KP6 1/4x2 Spring Loc
8066 KP7 3/8x2-11/16 Spring Loc
8067 KP8R 1/4x1-1/8 Round
8068 KP8S 1/4x1-1/8 Square
8069 KP8L 1/4x2-1/8 Square Long
8071 KP9S 3/8x1/1/8 Square
8074 KP10S 1/2x1/1/4 Square
8077 KP8XL 1/4x3-1/8 Square Extra Long
8179 KP10L 1/2x2-1/4 Square Long
RS Rapit Regulator Set (10 bx)
  • 8086 RS156 1 RB-50 Rapit spring bearing; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
  • 8085 RS256 2 RB-50 Rapit spring bearings; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
  • 8233 RS356 1 RB-50 Rapit spring bearing; 1 RB-25T threaded Rapit solid bearing; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
RS156 1 spring bearing
RS356 1 spring 1 solid bearing
RS256 2 spring bearings
JDS Jiffy Damper w/Spring & Bearings
8094 6in
8096 8in
8137 10in
SP Access Door Latch Assembly
8106 SP10 3/8
8107 SP20 1/2
K2-2 1/4in Round Duct 2in Standoff Dial Regulator (Box of 10)
SRE516 5/16in Slide Rapit Extension
The Slide Rapit Extension provides a fast method for extending the length of a rapit spring end bearing 2’’.
REC14 Rapit Extension 2-3/4 Long - Converts RB50 to 1/4 Square Rod (Box of 10)
Creates a 2-3/4'' extension when using a standard RB50 Rapid End Bearing; for use with 1/4'' square reguators.
KS7 1/4in Jiffy Set for Dampers Up to 20in (Box of 10)
Slip the washer and handle over the threaded square end bearing, wing nut locks the damper in position, position of the handle indicates the position of the damper in the duct, For use on round or square ducts, Consists of -
  • 1/4 Threaded Bearing
  • Handle, Wing Nut, Beveled Washer
  • KP6 Spring Loc Bearing
KSR19 3/8in Dial Set for Dampers Up to 20in
The 3/8” bearings and regulator are suitable to use on round as well as square duct, Clear markings on the regulator indicate the damper position which canbe locked securely by a wing nut, Also available in stainless steelregulator only Consists of -
  • KR3 Regulator
  • KP9S Square End Bearing
  • KR9R Round End Bearing
KS145L 1/4in Quadrant Set - Long (Box of 10)
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of the damper, The frame is marked to show the exact position of the damper, For use on square or round ducts, Consists of -
  • K-2 regulator
  • KP-8L long square end bearing
  • KP-6L long spring loc bearing
KS385L 3/8in Quadrant Set Long for Dampers to 20in
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of the damper, The frame is marked to show the exact position of the damper, For use on square or round ducts, Consists of -
  • K-4 quadrant
  • KP-7L long spring loc bearing
  • KP-9L long square end bearing
KS385 3/8in Quadrant Set for Dampers to 20in
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of the damper, The frame is marked to show the exact position of the damper,For use on square or round ducts, Consists of -
  • K-4 quadrant
  • KP-7 spring loc bearing
  • KP-9S long square end bearing

Insulation Adhesives / Duct Sealers

AFG-1404-181BFX Silver Foil 3"x100' Indoor/Outdoor Foil Grip Tape
Foil-Grip 1404-181-BFX is a UL 181B-FX listed pressures sensitive rolled mastic sealant.
SureGrip 404 Indoor Application Fiber Free Solvent Base Duct Sealant
Sure-Grip 404 is a fiber-free, solvent based, synthetic rubber duct sealant.
SG 404 - 1 Gallon
SG 404 - 11oz Tubes
DP77 Industrial Spray Adhesive 12 oz
Features and Benefits:
  • Pressure Sensitive
  • Quick Drying
  • Permanent Bond
  • Lace-Like Web Spray Pattern
  • High Temperature Resistance - Bond Maintained After Exposure To Heat Up To 200° F
  • Non-Misting
  • No CFC’s
  • VOC Compliant
DP1010 WATER BASED DUCT SEALANT
  • Zero VOC
  • A premium, smooth water-based
  • UL listed, high velocity grey duct sealant for commercial and residential use
  • Qualifies for Leed™ Credit EQ 4:1
DP1010-02-01 Gallon
DP1010-02-12 Tube
DP1090 LOW VOC SOLVENT BASED DUCT SEALANT
  • Solvent Based, LEED Low VOC Duct
  • UL Classified, high velocity tan duct sealant for commercial use
  • Skins in less than a minute to help installers avoid the clean up commonly associated with solvent based duct sealers
  • Qualifies for Leed™ Credit EQ 4:1
DP1090-04-12 Tube
DP1090-04-01 Gallon
DP2502 WATER BASED DUCT LINER ADHESIVE
  • A water based, premium quality
  • UL classified duct liner adhesive
  • A higher viscosity version of DP 2501, specifically formulated for roller, brush or spray
  • Colored white
DP2502-01-54 54 Gallon White
DP2502-01-05 5 Gallon White
Chip Brush - 2in
Brush used to apply mastic
SSG-5 Adhesive
  • Duro Dyne SSG is a non-flammable water-based duct liner adhesive specifically formulated for spray application
  • SSG may be used for bonding low and high density duct liner or wrap to the interior or exterior of metal ductwork
  • SSG is formulated to work with Duro Dyne’s Super Sprayfast
  • Non-Flammable, wet or dry
  • Can be applied by spray
  • Non-toxic
  • 100% solvent free
  • Super quick grab to hold liner in place
  • Excellent coverage
  • ...
RPG1 Adhesive
  • Adhesive for bonding insulation material to sheet metal
  • Excellent tack and quick grab
  • Use with liner up to 3# density
WITLV Low Viscosity Water Based Adhesive (5 Gallon)
  • WIT-LV is a non-flammable water-based duct liner adhesive specifically designed for automated coil line use, rotobonder, and sprayer applications
  • LV factor provides a cost effective low viscosity product, with the aim of preventing clogs and providing easy clean up
DCEC Dyn-O-Coat 14oz Edge Coat
  • Dyn-O-Coat combines the flexibility of sealants with the quick drying advantage of aerosol to bring you a highly efficient Edge Coating
  • Simply spray on to encapsulate rips, tears and cut edges
DTWA Dyn-O-Tac Web Adhesive
  • This 4-1/2” wide web spray adhesive provides a versatile and strong bonding formula which is excellent for use on fiberglass, rubber and cotton liners
  • Non-chlorinated and non-ozone depleting
PAB40 40lb Canister ADH-Black
  • Duro Dyne PAB40/PAB187 is a web type, high solids, general purpose adhesive that bonds well to a wide variety of substrates, with one side or two side application
  • This black liner adhesive can also be used as an effective edge coating
  • It has a quick tack, is flexible, non-wrinkling and water proof
  • Use on a variety of surfaces including insulation, plastic, wood, ABS, FRP, foam, carpet, wall coverings, fiberglass, packaging, labeling and more
  • ...
PAC40 40lb Canister ADH-Clear
  • Low VOC & NO Methylene Chloride (Dichloralmethane)
  • PAC40 is a web type, high solids, general purpose adhesive which bonds well to a wide variety of substrates, with one side or two side application
  • It has a quick tack, is flexible, non-wrinkling and waterproof
  • Use on a variety of surfaces including insulation, plastic, wood, ABS, FRP, foam, carpet, wall coverings, fiberglass, packaging, labeling and more
  • ...
PAC12H 12ft Canister Hose
  • Duro Dyne Adhesive Canisters utilize a gun and hose assembly to apply the adhesive to insulation
  • The Hose, Gun and GunTip are sold separately from the canisters
  • Ordering Information about these accessories are available on all Canister Lit Sheets
PAG Canister Gun
  • Duro Dyne Adhesive Canisters utilize a gun and hose assembly to apply the adhesive to insulation
  • The Hose, Gun and GunTip are sold separately from the canisters
  • Ordering Information about these accessories are available on all Canister Lit Sheets
DLSN Duct Lock Sealant (5 Gallon)
DLSN Sealant is a grey, single-component, non-drying, permanently flexible material designed for sealing metals, and masonry surfaces without the need or requirement of a primer.
Stripper Cleaner & Lubricating Spray
  • An effective preventive maintenance system right at your fingertips
  • Galvanizing build-up is bad for job quality, production efficiency and profits
  • The Stripper is a degalvanizing agent that strips your machine of messy build up
  • It sprays on red for easy visibility
  • Simply Spray it on rollers of forming machines and press dies and the special ingredients get right to work and dissolve galvanized build up
  • ...

Insulation Fastening

BDEP Weld Pins w/Cup Washer
BDEP pins have unique washers designed to improve the quilting contour of the insulation surface.
26072 5000 pack 1/2in
26073 5000 pack 3/4in
26074 5000 pack 1in
PN Spotter Pin for Duct Liner (1000pk)
PN Spotter pins are manufactured with 14 gauge galvanized steel and are designed for use with LF Handheld Pinspotters.
26001 PN34 1/2in liner
26002 PN114 1in liner
26017 PC1 Spotter Clips for PN Pins (1000pk)
FSG250 Galv Flip Stix (100 bx)
A unique insulation hanger with a self stick base.
SAH Self Adhesive Hanger and Washer (100pk)
SAH Dynastick is an insulation hanger with a self-stick base and is sold with a steel washer.
26068 1-1/4in
26069 1-3/4in
26070 2in
26067 3/4in
26071 2-1/2in
FTC Econo-Point Weld Pins
Econo Point FTC weld pins utilize a specially pointed nail to assure uniform welding.
26072 5000 pack 1/2in
26073 5000 pack 3/4in
26074 5000 pack 1in
26131 3000 pack 1-1/8in
26226 3000 pack 1-1/2in
26227 3000 pack 2in
LPC1 Metal Washer for Dynastick and Stick-Tac (100pk)
LPC1 washers are included with most mechanical type fasteners.
BGT Duct Liner Standard Banger (1000pk)
Standard Bangers have two prong jaws to fasten to the sheet metal.
26033 BGT12 1/2in
26044 BGT100 1in
TBG Duct Liner Tripod Banger (1000pk)
Tripod Bangers feature three prong jaws for added stability when fastening the banger to the sheet metal.
26129 TBG12 1/2in
26130 TBG100 1in

Machinery

CCD110 COMPACT PINSPOTTER 27120
The CCD110, Capacitor Discharge Welder, is designed for the convenience and comfort of the operator.
FG MACH I and IIA AUTOMATIC BULK FEED PINSPOTTER w/5ft THROAT
The FG MACH I & IIA welds BDEP, CTC, SSP, CP & FTC type fasteners.
18001 Mach I
18003 Mach IIA
LF 2000 LN HAND HELD PINSPOTTER
The LF is a portable unit (9 lbs) that welds 14 gauge PN style pins to duct work up to 22 gauge, Insert a PN Pin into the magnetic tip and depress the trigger.
LS-5 Manual Insulation Cutter
For use with 1/2'' to 2'' liner The LS5 is a manual insulation cutter that slits fiberglass insulation to length and width.
LSU LINER SIZER
For use with 1/2'' to 2'' liner Duro Dyne’s LSU Advanced Liner Sizer is an enhanced version of the popular Model LS5 making it capable of cutting cotton fiber insulations, filter media and rubberized products as well as fiberglass duct liner.
MF-12 COMPACT PINSPOTTER
The MF-12 welds BDEP, CTC, SSP, CP, FTC, PN or LN type fasteners to ductwork up to 20 gauge.
PBF-510 HEAVY DUTY PINSPOTTER
The PBF-510 welds BDEP, CTC, SSP, CP, FTC, PN or LN type fasteners to ductwork up to 18 gauge.
PINSPOTTER PARTS
17078 SQE2 Repair Kit
17189 Upper Plate (5 pk)
17190 Lower Plate (5 pk)
17192 Lower Weld Tip
17231 RH Dwell Cylinder
17253 RH Sensor Block
17283 RH Trigger Actuator Assembly
17356 FG Adj Muffler
17372 FG Footswitch
17399 RH Floating Weld Cable
PLS AUTOMATIC INSULATION CUTTER
For use with 1/2'' to 2'' liner The PLS is used for production line cutting of fiberglass insulation.
RH MACH IIA ROLLING HEAD AUTOMATIC PINSPOTTER
RH MACH IIA welds BDEP, CTC, SSP, CP & FTC type fasteners to ductwork up to 18 gauge.
SUPER SPRAYFAST ADHESIVE APPLICATOR
The Super Sprayfast is an air powered adhesive spray system designed for use with 5 gallon or 55 gallon containers of Duro Dyne water based adhesives.
FDCC Connector Dispenser
The Duro Dyne Connector Dispenser can relieve many of the difficulties associated with the handling of flexible connector.
FDCS-10 Cutting Shear
FDCC Shear The FDCS-10 Cutting Shear cuts material up to 18 gauge.
Dyn-O-Wrap Dispenser
Perfect solution for storing and dispensing different sizes and types of Dyn-O-Wrap ▪ Allows for easy application (no awkward maneuvering) ▪ Keeps wrap off of the floor to prevent dirt from adhering to the adhesive

Screws & Rivets

Super Saber Point Screws
Designed for light-to medium-gauge materials, the Super Saber Point offers onestep fastening; Its time saving performance is related to the saber-sharp piercing point with a “fine-cut” machine thread, which pierces the metal upon contact; Once pierced, the thread propels the screw through metal rapidly and almost without effort.
8x1-1/2
8x3/4
8x1/2
8x1
8x2
Pro Point Screws - High Head
High Head Pro Point Screws are self drilling and tapping screws featuring an oversized head that increases stability when positioning or installing screws.
8x3/4
10x3/4
10x1-1/2
SAT8x2W Super Saber Point Screw white head
Designed for light-to medium-gauge materials, the Super Saber Point offers onestep fastening; Its time saving performance is related to the saber-sharp piercing point with a “fine-cut” machine thread, which pierces the metal upon contact; Once pierced, the thread propels the screw through metal rapidly and almost without effort.
15180 8x2/100pk
15181 8x2/1000pk
15179 8x2/3000pk
10HHx3/4 High Head Pro Point Screws
High Head Pro Point Screws are self drilling and tapping screws featuring an oversized head that increases stability when positioning or installing screws.
PPT10HHx3/4 (500 pk)
PPT10HHx3/4 (1,000 pk)
BKTAB10HHx3/4 (5,000 pk)
NTAB10HHx1-1/2 (2000 pk)
High Head Pro Point Screws are self drilling and tapping screws featuring an oversized head that increases stability when positioning or installing screws.
NTAB10HHx3/4 (3500 pk)
High Head Pro Point Screws are self drilling and tapping screws featuring an oversized head that increases stability when positioning or installing screws.
TAB10HHx3/4 Tapper Screws (5000pk)
Designed for light-to medium-gauge materials, the Super Saber Point offers onestep fastening and features an oversized head that increases stability when positioning or installing screws.
Pin Rivets (1000pk)
Pin Rivets are strong, hollow rivets assembled onto a solid mandrel; They are manufactured to strict quality control standards and are available in a wide range of sizes and styles to provide the proper rivet for every type of application; Pin Rivets are inserted and set from the same side; They are particularly practical where there is no access to the reverse side of the work.
23060 AA42DT Aluminum/Alumium
23002 SS42DT Steel/Steel
23004 SS44DT Steel/Steel
23095 SS46DT Steel/Steel
23005 SS48DT Steel/Steel
23013 XX42DT Stainless/Stainless
23014 XX44DT Stainless/Stainless
PPC10HHx3/4 High Head Pro Point Screws (100pk) 410 Stainless Steel
High Head Pro Point Screws are self drilling and tapping screws featuring an oversized head that increases stability when positioning or installing screws.

DUCT INSULATION & DUCT BOARD

Ap Armaflex Duct Liner (Non- Self Adhering)
AP Armaflex and Armaflex FS (Fire and Smoke) duct liner and wrap are the original fiber-free, closed-cell, thermal and acoustical insulation for ducts.
ADR120563100 56-1/4"x100'x1/2"
ADR12059011 59"X100'X1/2"
ADR100563050 56-1/4"X50'X1"
AD510059050 59"X50'X1"
AP Spiralflex Roll
AP Spiralflex is the first fiber-free, lightweight and conformable elastomeric duct liner specifically designed for spiral ducts.
QuietR® Rotary Duct Liner
  • Absorbs fan and air turbulence noise and reduces popping noises within sheet metal ducts
  • Outstanding thermal and acoustical performance
  • Bacterial and fungal growth resistant
634200 R2.2 1/2x47 100ft
634464 R2.2 1/2x56.25 100ft
634213 R2.2 1/2x59 100ft
634235 R4.2 1x47 100ft
634198 R4.2 1x56.25 100ft
634221 R4.2 1x59 100ft
634227 R6.3 1-1/2x47 50ft
634472 R6.3 1-1/2x56.25 50ft
634483 R6.3 1-1/2x59 50ft
634857 R8 2x56.25 50ft
SOFTR® Duct Wrap FRK
  • Condensation control
  • Enhanced comfort control
  • Easy to clean surface
  • Flexible and easy to install
  • Type 75 or 3/4 lbs/cubic foot
DWT75 1.5x48 R4.2 100ft
DWT75 2.2x48 R6.0 75ft
DWT75 3x48 R8.3 50ft
QuietZone® Spiral Duct Liner 48x120 (Box of 6)
  • Outstanding thermal and acoustical performance
  • Cleanable surface with a black mat facing that provides a smooth, durable surface
  • Bacterial and fungal growth resistant
R4.3 - 1in
R6.5 - 1-1/2in
R8.7 - 2in
QuietR® Duct Board 1x48x120 R4.3
  • Absorbs noise and reduces popping noises caused by expansion, contraction and vibrations
  • Assured thermal R-value performance
  • Bacterial and fungal growth resistant
  • Thermal/acoustical insulation board plus jacket forms a single component duct system, thus reducing inspection time
  • Lightweight boards are easier to transport and handle than insulated sheet metal ducts
  • Virtually eliminates air leakage thus saving energy and removing the need for system overdesign
  • ...
3M™ Fire Barrier Duct Wrap 615+
3M has developed 3M™ Fire Barrier Duct Wrap 615+ to be the only fire-rated duct wrap product youll need to help protect both grease ducts and air ducts, in an easy to install format (lightweight, flexible) while passing the necessary fire tests to achieve up to 2-hour fire-resistance requirements.
RA-26 Appliance Insulation 1x72 - 120ft 2/EORLS4
RA Series Appliance Insulation products are lightweight yellow blankets of inorganic glass fibers bonded with a thermoset resin; designed to provide superior dimensional stability, excellent thermal and acoustical performance, and easy handling and installation

FLEXIBLE AIR DUCT

HART & COOLEY FLEXIBLE AIR DUCT

F206 Sleeve - R-6.0 - Silver Jacket - 5 FT
  • Metalized polyester jacket
  • UL-classified
  • R-4.2 F204 / R-6.0 F206 / R-8.0 F208 (R-values valid if sleeve is used on relatively sized duct)
  • 5' length
  • Starter cone included in each carton
6in
7in
8in
10in
12in
14in
16in
F208 Sleeve - R-8.0 - Silver Jacket - 5 FT
  • Metalized polyester jacket
  • UL-classified
  • R-4.
4in
5in
6in
7in
8in
10in
12in
14in
16in
FB216 Air Duct - R-6.0 - Silver Jacket - 25 FT
  • Metalized polyester jacket reinforced with fiberglass scrim
  • Double-ply, black polyester core 12" W.
4in
6in
7in
8in
10in
12in
14in
16in
18in
20in
FB218 Air Duct - R-8.0 - Silver Jacket - 25 FT
  • Metalized polyester jacket reinforced with fiberglass scrim
  • Double-ply, black polyester core 12" W.
4in
6in
7in
8in
10in
12in
14in
16in
18in
20in
DN Nylon Dyn-O-Tie (Bag of 50)
Whenever your job calls for securing round flexible duct to outlets, pipes or fittings, you can do the job better, faster, and at low cost using DYN-O-TIES™, flexible duct ties.
7004 36in
7005 48in
DTWD SS Dyna-Clamp (box of 100)
Stainless Steel Adjustble Clamp
7008 DT10WD 10in
7009 DT12WD 12in
7010 DT15WD 15in
7011 DT16WD 16in
7013 DT18WD 18in

THERMAFLEX FLEXIBLE AIR DUCT

FlexFlow Elbow
The FlexFlow Elbow maximizes airflow by economically forming any brand and any size of commercial or residential flexible duct into a highly efficient 90° elbow.
KM R-6 INSULATED AIR DUCT - 25FT
Strong polyester film laminated and encapsulating a heavy, corrosion resistant steel wire helix, forms the inner core and supports a thick blanket of fiberglass insulation.
6in
8in
10in
12in
14in
16in
M-KC R-6 INSULATED AIR DUCT - 25FT (PRO SERIES)
Our premier product, the M-KC Flexible Duct offers a comprehensive solution to your HVAC duct needs.
4in
5in
6in
7in
8in
9in
10in
12in
14in
16in
18in
20in
M-KE R-6 ACOUSTICAL INSULATED AIR DUCT - 25FT (PRO SERIES)
The M-KE Acoustical Duct offers exceptional sound control.
4in
5in
6in
7in
8in
9in
10in
12in
14in
16in
18in
20in
S-LD R-6 AIR CONNECTOR - 25FT (PRO SERIES)
Advantages of S-LD Air Connector
  • Reduced total installed cost-fast economical installation
  • Superior insulation and thermal performance
  • Easily shaped to fit oval inlets and fittings
  • All components are self-extinguishing and will not support flame
  • Underwriters Laboratories UL181 listed and complies with NFPA Standards 90A and 90B
  • Complies with most state and federal standards or codes
  • Unique construction will not unravel when cut
  • Suitable for air venting and drying applications
  • ...
4in
5in
6in
7in
8in
9in
10in
12in
14in
S-LP-10 NON-INSULATED AIR DUCT - 25FT (PRO SERIES)
Non-insulated air connector with extremely strong woven fiberglass fabric with flame retardant coating, permanently bonded to a corrosion resistant coated spring steel wire helix.
4in
6in
8in
10in
12in
14in
S-TL NON-INSULATED AIR DUCT - 4" - 14" 25FT & 16" - 20" 15FT (PRO SERIES)
16" and above are ONLY 15ft sections! Non-insulated UL181 Class 1 flexible air duct, extremely strong with heavy fiberglass cloth fabric permanently bonded to a corrosion resistant spring steel wire helix.
4in
6in
8in
10in
12in
14in
16in
18in
20in

FILTERS AND HUMIDIFIER PADS

GRILLES, REGISTERS & DIFFUSERS

Commercial Registers & Grilles

DMR Spiral Register
  • supply/return register with adjustable double deflection blades and volume damper
  • designed for direct mounting
  • rectangular register taps are not required
  • register is made of galvanized sheet steel
  • damper is made of electro-galvanized
13x3
17x3
21x3
17x6
21x6
25x6
33x6
821 Steel Register Vertical Fins, MS damper
  • All-steel construction
  • Vertical, adjustable face bars
  • Horizontal multi-shutter valve
  • Bright White finish
10x4
10x6
10x10
12x4
12x6
12x8
12x12
14x6
14x8
14x14
16x8
20x12
24x6
92VHV Steel Double Deflection Register, OBD damper
  • All-steel construction
  • Vertical front bars
  • Horizontal second bars
  • Adjustable face bars may be set to any desired deflection
  • Opposed-blade damper
  • Larger sizes available in multiple-piece construction
  • Bright White finish
12x6
14x6
14x8
14x12
16x12
18x6
20x6
20x8
20x12
24x6
24x8
24x10
24x12
30x6
30x8
30x10
30x12
94A Steel Return Air Grille, 35-degree Fixed Blade (No Damper)
  • All-steel construction
  • 3/4" spaced fins set at 35 degree, horizontal face bars
  • Larger sizes available in multiple-piece construction
  • Bright White finish
10x6
12x6
14x6
14x8
14x14
16x16
20x14
20x20
24x12

Commercial T-Bar (drop ceiling)

444 — Aluminum Renovator Series Diffuser 4-way, Insulation Blanket
  • Aluminum face
  • Unique deflector apertures
  • Air distributed in thin layers along ceiling surface allowing optimum mixing of conditioned air
  • Formed galvanized steel back panel
  • Frame includes four seismic safety connections
  • Back plate covered with glass fiber insulation to reduce condensation
  • Aluminum foil vapor barrier protects insulation from harmful effects of condensation
  • Insulation prescored to accommodate collar size desired
  • Accepts snap-in collar (5400 Series) (6" to 12")
  • 444 - 14" collar is factory-installed
  • Utilizes butterfly damper (3800 Series) inserted in collar
  • Damper adjusted through diffuser face to allow proper air balancing
  • Bright White finish
  • Available sizes: overall size 23 3/4" x 23 3/4"
  • ...
5400PP — Push Pins for 5400 Series Ring Collar
  • Attaches 5400 collar to molded fiberglass back for the following products:
    • 659TI 1 1/4" long
    • PFTI 1 1/4" diameter head
    • RENP
    • RENPS/RENPS R6
    • RE5TI
    • 96AFBTI
    • REN4
    • HVS R6
    • SRET/SRET R6
PD — Steel Perforated Panel 24x24
  • Face only return for plenum ceiling
  • White finish
RENP — Steel Perforated Return with R4.2 Molded Insulation
  • Perforated steel face
  • R4:2 molded fiberglass back panel
  • Accepts 6" to 14" unique tab collar (6400 series) or 6"-16" unique snap-in collar (5400 and 5400PP series; 16" and 18" only for R4.
SMF — Surface Mount Frame for T-bar Diffusers 24x24
  • Aluminum construction
  • Permits installation of standard T-Bar diffusers in a plaster ceiling
  • Accepts standard T-Bar diffusers
  • Bright White finish
  • Available sizes (inches): 12x12, 24x12, 24x24, 24x48
659T 20x20 Steel Lanced Return Air Filter Grille, 1/3in Fin Spacing
  • Steel construction
  • Lanced-face design with 1/3" blade spacing
  • Flush, removable face with concealed latches and hinges can be installed in any direction
  • Uses standard 1" disposable filters (not furnished)
  • Bright White finish
2'x4' Eggcrate Ceiling Panel
Egg Crate Ceiling Grille is an important tool in helping design an energy efficient data center, designed to work with the natural properties of rising hot air.
FPD3 Steel 4-way Diffuser, 3 Cone Design, 6-14in Fixed Collars
  • Steel construction
  • Provides high air volume delivery
  • 360-degree air diffusion
  • Three cone fixed core
  • Fixed collar 6" to 14"
  • Unique 2" high collar permits easy flex connections
  • Utilizes butterfly damper (3800 Series) inserted in collar
  • Damper adjustable through face
  • Formed steel back panel
  • Bright White finish
  • Available size: overall size 23 3/4" x 23 3/4"
  • ...
6in
8in
10in
12in
14in
PFTI Steel Perforated Face, Return Air Filter Grille with Molded Insulated Back
  • Steel construction
  • Perforated face design
  • Flush, removable face with concealed latches and hinges, can be installed in any direction
  • Molded fiberglass back, available in R4-2/10 or R6
  • Accepts 6" to 14" unique tab collar (6400 series) or 6" to 16" unique snap-in collar (5400 and 5400PP series; also accepts standard spin-in collar
  • Frame includes four seismic safety connections
  • Uses standard 1" disposable filters (not furnished)
  • Bright White finish
  • Available size: 20" x 20", overall 23 3/4" x 23 3/4"
  • ...
RE5T Aluminum Eggcrate Return Air Grille - Bright White - 22x22
  • All aluminum construction
  • Eggcrate style face
  • Mount flush with T-Bar ceilings
  • Bright White or Mill Aluminum finish
  • 22" x 22" with extended frame (overall 23 3/4" x 23 3/4") for 24" x 24" openings
3800 Round Butterfly Damper for T-bar Diffusers
  • Adjustable butterfly damper with removable handle (included)
  • For use with 5400 and 6400 Series collars
  • Golden Sand finish
  • Available sizes (inches): 6, 7, 8, 9, 10, 12, 14
3806
3807
3808
3810
3812
3814
DPD — Steel Plate Diffuser, 6-14in Fixed Collars
  • Aesthetically appealing, single-face plate design
  • 360 degree air diffusion pattern
  • Detachable face plate
  • 2" fixed collar
  • Optional R6 insulated back (DPD R6)
  • Bright White finish
  • Available sizes (inches): 6, 8, 10, 12, 14
6in
8in
10in
12in

Residential Baseboard Registers & Grilles

406 Steel Baseboard Diffuser 4.5in high
  • All-steel construction
  • Blankets wall or window area
Golden Sand
Bright White
15in
18in
407 Steel Baseboard Return 4.5in high - 18in
  • All-steel construction
  • Complementary return air grille for #406 supply
Golden Sand
Bright White
462 Steel 2 Ft Baseboard Diffuser
  • All-steel construction
  • Two-foot length
  • Airfoil valves reduce resistance
  • Equal air distribution over the length of the diffuser
  • Face can be easily removed
Golden Sand
Bright White
464 Steel 4 Ft Baseboard Register
  • All-steel construction
  • Four-foot length
  • Airfoil valves reduce resistance
  • Equal air distribution over the length of the diffuser
  • Dual valves
  • Face can be easily removed
Golden Sand
Bright White
655 10x6 Steel Baseboard Register, Plate Damper, Base Projection
  • All-steel construction
  • 1/3" spaced fins set at 20 degrees
  • Volume-control damper
  • Bright White enamel finish
657 Steel Baseboard Return
  • One-piece steel construction
  • 1/3" spaced fins set at 20 degrees
  • 7/8" margin turnback
  • Exceptional free area
  • Install with fins upward or downward for best duct concealment
  • Complementary return air grille for #654 supply or #664 supply
Golden Sand
Bright White
10x6
10x8
12x6
12x8
14x6
14x8
24x6
24x8
30x6
30x8
658 Steel Baseboard Return, Base Projection
  • All-steel construction
  • 1/3" spaced fins set at 20 degrees
  • Complementary return air grille for #655 supply
  • Bright White enamel finish
12x6
14x6
14x8
24x6
24x8
30x6
30x8
664 Steel Baseboard Register, Multi-Shutter Damper
  • All-steel construction
  • 1/3"-spaced fins set at 20 degrees
  • 7/8" margin turnback
  • 1-5/8" depth when fully opened
  • Exceptional free area
  • Ideal for shallow duct installations
  • Multi-shutter valve
  • Bright White enamel finish
12x6
12x8

Residential Floor Registers & Grilles

210 Heavy Duty Steel Floor Register - 10x12
  • All-steel construction
  • Provides firm, smooth surface
  • Extremely rigid
  • Free area averages over 75%
  • Toe-operated valve control
  • Golden Sand enamel finish
265 Heavy Duty Steel Floor Grille
  • All-steel construction
  • Provides firm, smooth surface
  • Extremely rigid
  • Free area averages over 75%
  • Golden Sand enamel finish
4x24
6x10
6x12
6x14
6x20
6x24
6x30
8x10
8x12
8x14
8x16
8x24
8x30
10x10
10x12
10x14
10x20
10x24
10x30
12x12
12x14
12x20
12x24
12x30
14x30
16x20
16x30
18x30
20x30
420 Steel Toe Kick
  • All-steel construction
  • Heavy-gauge, stamped face
  • Multi-angle fins
Golden Sand
Bright White
10X2
12X2
14X2
421 Steel Floor Register
  • All-steel construction
  • Multi-angle fin setting
  • Rolled fin for strength and safety
  • Welded construction
  • Foot-operated dial control
  • Heavy-gauge, stamped face
Golden Sand
Bright White
2X10
2X12
2X14
4X8
4X10
4X12
4X14
6X10
6X12
6X14
531 Aluminum Floor Register
  • Extruded aluminum construction
  • Corrosion-resistant, high strength
  • Heavy cross-bracing at strategic intervals
  • Dual multi-shutter valves for adjustable air pattern
  • Nylon slide valve operators
  • Satin-anodized finish
4x10
4x14
6x12 [will take 3 weeks to make]

Residential Sidewall/Ceiling Registers & Grilles

11 Duct Ring for #16 Diffuser
For installation of #16 diffuser when not using a damper (Golden Sand finish)
6in
8in
10in
12in
12 Butterfly Damper for #16 Diffuser
  • All-steel construction
  • Controls air volume evenly over entire #16 diffuser
  • Removable knob operator for adjustment from closed to fully open
  • Golden Sand enamel finish
6in
8in
10in
12in
16 Steel Round Diffuser - Bright White
Step down diffuser rings deflect air stream 360 degrees
6in
8in
10in
12in
14in
650 Steel Return Air Grille, 1/3in Fin Spacing
  • All-steel construction
  • 1/3" spaced fins set at 20 degrees
  • Exceptional free area
  • 5/16" Margin Turnback
  • Bright White finish
6x6
8x6
8x8
10x4
10x6
10x8
10x10
10x20
12x4
12x6
12x8
12x10
12x12
14x4
14x6
14x8
14x10
14x12
14x14
14x20
16x6
16x8
16x10
16x12
16x14
16x16
16x20
18x6
18x8
18x12
18x18
20x6
20x8
20x10
20x12
20x14
20x16
20x18
20x20
20x24
24x6
24x8
24x10
24x12
24x14
24x18
24x20
24x24
30x4
30x6
30x8
30x10
30x12
30x14
30x16
30x20
30x24
36x12
659 Steel Return Air Filter Grille, 1/3in Fin Spacing
  • All-steel construction
  • 1/3" spaced fins set at 20 degrees
  • Effectively conceals filter
  • Use standard 1" thick disposable filters (not included)
  • Removable face for easy installation and cleaning
  • Equipped with adjustable filter retainers
  • Bright White finish
14x14
14x20
14x24
14x25
16x20
16x25
20x20
20x25
24x24
25x20
30x20
661 Steel 2-way Register, MS damper, 1/3in Fin Spacing
  • All-steel construction
  • Used for ceiling or sidewall installations
  • For heating or cooling
  • Ideal for shallow duct installations
  • Two-way deflection
  • 1/3" spaced fins set at 20 degrees
  • Galvanized multi-shutter valve
  • 1-5/8" depth when fully opened
  • Interlocking valve louvers for positive shut-off
  • Bright White finish
  • ...
6x4
6x6
8x4
8x6
8x8
10x4
10x6
10x8
10x10
12x4
12x5
12x6
12x8
14x4
14x6
14x8
16x8

SHEETS

304 Stainless Steel Sheet - #2B Finish
  • 304 stainless steel 2B finish is a mill finish, which is smooth and NOT the brushed finish commonly seen on kitchen appliances
  • 304 stainless steel 2B finish is light gray in color.
14GA/48x120
16GA/48x120
18GA/48x120
20GA/48x120
22GA/48x120
24GA/36x96
24GA/36x120
24GA/48x120
26GA/48x120
304 Stainless Steel Sheet - #4 Finish
  • 304 stainless steel sheet #4 finish is the brushed finish commonly seen on kitchen appliances and backsplashes
  • 304 stainless steel sheet #4 finish has a PVC film on one side to help protect against scratching during fabrication and installation.
14GA/48x120
16GA/48x120
20GA/48x96
20GA/48x120
24GA/36x96
24GA/48x120
ALUMINUM SHEET 3003 TEMPER H14
3003 Aluminum is alloyed with 1-2/10% manganese, which increases the strength of 3003 over commercially pure aluminum; H14 designates the temper, and means that 3003 has been strain hardened and partially annealed.
.025 36x96
.025 36x120
.032 36x96
.032 36x120
.032 48x120
.040 48x120
.050 48x120
.063 48x120
COLD ROLLED STEEL SHEET 48x120
  • Cold rolled steel is essentially hot rolled steel that has had further processing; the steel is processed further in cold reduction mills, where the material is cooled (at room temperature) followed by annealing and/or tempers rolling
  • This process will produce steel with closer dimensional tolerances and a wider range of surface finishes
  • The term Cold Rolled is mistakenly used on all products, when actually the product name refers to the rolling of flat rolled sheet and coil products
  • ...
16 GA
18 GA
GALVANIZED STEEL SHEET
  • Galvanized steel sheet refers to a process that covers mild steel with a layer of zinc to provide good corrosion resistance;
  • G60 zinc coating equates to 6/10 oz/sf of sheet; (G90 9/10 oz/sf in 60x120 sheets)
12GA / 48x120
14GA / 48x120
16GA / 48x120
18GA / 48x120
18GA / 60x120
20GA / 36x96
20GA / 48x96
20GA / 48x120
20GA / 60x120
22GA / 48x96
22GA / 48x120
22GA / 60x120
24GA / 36x96
24GA / 36x120
24GA / 48x96
24GA / 48x120
24GA / 60x120
26GA / 36x96
26GA / 36x120
26GA / 48x96
26GA / 48x120
26GA / 60x120
28GA / 36x96
28GA / 36x120
28GA / 48x96
PAINT GRIP STEEL SHEET 48X120
  • Hot-dipped galvanized commercial steel is carbon steel sheet coated with zinc on two sides by the continuous hotdipped process
  • This process results in a layer of zinc on each side of the steel sheet that is tightly adhering to the steel thru the formation of an iron-zinc alloy bonding layer that is formed by a diffusion process while the heated steel strip is in contact with the molten zinc
  • ...
20GA/48x120
24GA/48x120
48x120 16 GA Expanded Sheet
  • Expanded metal is a sheet product that has been slit and stretched to a wide array of diamond shaped openings
  • Steel expanded metal offers savings in weight and metal, free passage of light, liquid, sound and air, while providing a decorative or ornamental effect.
PVS 4x4 COATED STEEL SHEET
The PVS Coating Process Begins with hot dipped galvanized steel, G60 or better that is cleaned and treated for coating Then a special primer is baked onto both sides Finally, a special 4 mil Polyvinyl chloride coating is baked onto either one side (4x1) or both sides (4x4)
22GA / 48x120
26GA / 48x120

SHEET METAL DUCT SYSTEM

Snap Lock Pipe & Elbows

24in JT 26GA SNAP LOCK PIPE
3
4
5
6
7
8
9
10
12
60in JT 26GA SNAP LOCK SEALED PIPE
Pre-applied sealant along the entire length of the joint creates an air-tite seal.
3
4
5
6
7
8
9
10
12
14
16
18
24in JT 30GA SNAP LOCK PIPE
3
4/28ga
5
6
7
8
10
12
10FT JT 30GA SNAP LOCK SEALED PIPE
Pre-applied sealant along the entire length of the joint creates an air-tite seal.
4
6
7
60in JT 30GA SNAP LOCK SEALED PIPE
Pre-applied sealant along the entire length of the joint creates an air-tite seal.
3
4
5
6
7
8
10
12
26GA 90 ADJUSTABLE ELBOW
3
4
5
6
7
8
9
10
12
14
16
18
24
28GA 90 ADJUSTABLE ELBOW
10
12
30GA 90 ADJUSTABLE ELBOW
3
4
5
6
7
8

Register Boots

PH4 90 DEGREE REGISTER BOOT
2-1/4x10x5
2-1/4x10x6
2-1/4x12x6
2-1/4x14x6
4x10x4
4x10x5
4x10x6
4x10x7
4x12x6
4x12x7
4x12x8
4x14x6
4x14x7
4x14x8
6x10x6
6x10x7
6x12x6
6x12x7
6x12x8
6x14x6
6x14x7
6x14x8
PH5 90 DEGREE BASEMENT BOOT w/EARS
4x10x6
6x10x6
6x12x6
6x14x6
PH7 STRAIGHT REGISTER BOOT
2-1/4x10x5
2-1/4x10x6
2-1/4x12x6
2-1/4x14x6
4x10x4
4x10x5
4x10x6
4x10x7
4x12x6
4x12x7
4x14x6
4x14x7
4x14x8
6x10x6
6x10x7
6x12x6
6x12x7
6x12x8
6x14x8
PH3 END REGISTER BOOT
2-1/4x10x5
2-1/4x10x6
2-1/4x12x6
4x10x4
4x10x5
4x10x6
4x10x7
4x12x6
4x12x7
4x14x6
4x14x7
4x14x8
6x10x6
6x10x7
6x12x6
6x12x7
6x12x8
6x14x8
PH3 END REGISTER BOOT - LEFT HAND
2-1/4x10x6
2-1/4x12x6
4x10x6
4x12x6
PH3 END REGISTER BOOT - RIGHT HAND
2-1/4x10x6
2-1/4x12x6
4x10x6
4x12x6
124R 90 REGISTER BOOT
4x10x6
4x12x7
355 STRAIGHT OVAL REGISTER BOX
4x10x6
4x12x7
360 4X10X6 ANGLE OVAL REGISTER BOX
1020 90 STACK BOOT
2-1/4x12x6
3-1/4x10x4
3-1/4x10x6
3-1/4x10x7
3-1/4x12x6
3-1/4x12x7
1024 STRAIGHT STACK BOOT
2-1/4x12x6
3-1/4x10x4
3-1/4x10x6
3-1/4x12x6
3-1/4x14x7
3-1/4x14x8
1019 3-1/4x END STACK BOOT
10x6
10x7
12x6
12x7
14x7
14x8

Trunk Duct & Fittings

60in CROSSBROKE TRUNK DUCT - E-LOCK
  • Features (Duct includes 2 halves)
  • Safety edge - protects installer from cuts
  • Easy to adjust after assembly
  • Safer and easier to handle
  • Hemmed male leg gives more rigidity
  • 26 gauge galvanized - 48”, 60”, and 96” Lengths
  • 8 x 8 through 32 x 8 & 10 x 10 through 30 x 10
  • Attached S-cleat and includes drives
  • Cross broken for extra strength
  • ...
8x8
10x8
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
22x10
24x8
24x10
24x12
25x10
30x8
30x10
96in CROSSBROKE TRUNK DUCT - E-LOCK
  • Trunk Duct includes two halves
  • 26 gauge galvanized - 30”, 36”, 48”, 60”, and 96” Lengths
  • Furnished in Button Snaplock with S-Cleat & Drive Connections
  • Cross Broken for Extra Stiffening Strength
  • E-Lock Duct safety edge
8x8
10x8
12x8
14x8
16x8
18x8
20x8
24x8
1145 FLAT 45 ANGLE (SQUARE)
8x8
10x8
10x10
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
24x8
24x10
24x12
1146 FLAT 90 ELBOW (SQUARE)
8x8
10x8
10x10
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
24x8
24x10
24x12
1141 VERTICAL 45 ANGLE (SQUARE)
8x8
10x8
10x10
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
24x8
24x10
24x12
1140 VERTICAL 90 ELBOW (SQUARE)
8x8
10x8
10x10
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
24x8
24x10
24x12
1102 TRUNK TRANSITION - TAPERED TO ONE SIDE
10x8 to 8x8
12x8 to 8x8
12x8 to10x8
14x8 to10x8
14x8 to12x8
16x8 to 10x8
16x8 to12x8
16x8 to 14x8
18x8 to 10x8
18x8 to12x8
18x8 to14x8
18x8 to16x8
20x8 to 10x8
20x8 to 12x8
20x8 to 14x8
20x8 to16x8
20x8 to18x8
24x8 to 10x8
24x8 to 12x8
24x8 to 14x8
24x8 to 16x8
24x8 to 18x8
24x8 to 20x8
14x10 to 12x10
16x10 to 12x10
20x10 to 12x10
20x10 to 14x10
20x10 to 16x10
24x10 to 20x10
10x10 to 10x8
16x10 to 16x8
20x10 to 20x8
24x10 to 20x8
24x10 to 24x8
24x12 to 16x8
24x12 to 20x8
24x12 to 24x8
24x12 to 24x10
1100 STRAIGHT COLLAR
8x8
10x8
12x8
14x8
16x8
18x8
20x8
20x10
22x10
24x8
24x10
24x12
25x10
30x8
30x10
1110 END CAP
8x8
10x8
10x10
12x8
12x10
14x8
14x10
16x8
16x10
18x8
20x8
20x10
22x10
24x8
24x10
24x12
25x10
30x8
30x10
1147 OFFSET COLLAR
8x8
10x8
12x8
14x8
16x8
18x8
20x8
24x8
1109 TRANSITION COLLAR
8x8
12x8
14x8
16x8
18x8
20x8
24x8
1111 RETURN AIR FRAME
12x6 Regular
14x6 Regular
30x6 Regular
12x6 Heavy Duty
14x6 Heavy Duty
24x6 Heavy Duty
30x6 Heavy Duty
FILTER RACK FOR 1in FILTER
14x20
14x25
16x20
16x25
20x20
1101 TRUNK REDUCER
2x10
4x10
6x10
2x8
4x8
6x8
1054 17x35 JOIST PANNING
1073 ADJUSTABLE PLENUM SIDE
14x36
14x48
16x36
16x48
18x36
18x48
20x36
20x48
22x48
24x36
1072 ADJUSTABLE PLENUM TOP
18x18
20x20
24x24
26x26
30x30
1104 23-3/4in S-CLEAT
DRIVE CLEAT
8in
10in
RETURN AIR PACKAGE
Complete package consisting of (shipped knocked down in one carton):
  • 1 - Starting Collar
  • 2 - 30” Duct Sections
  • 1 - RA Plenum with
  • 1 - 1” Filter Rack
  • 6 - 10” Drive Straps
20x10/20x16
25x10/25x16
20x10/20x14
FURNACE BOX
  • 26 gauge galvanized steel
  • Fits most furnace sizes
  • Raises low profile furnace from ground
  • Easy access to filter for service
17x28
21x28
RETURN AIR SUPPORT BOX FOR FILTERS
36in

Oval Pipe & Fittings (Wall Stack)

OVAL PIPE 30GA JOINT
100 in x 6 in
100 in x 7 in
100 in x 8 in
113 in x 6 in
113 in x 7 in
113 in x 8 in
106NC OVAL TO ROUND REVERSE BOOT - NO CRIMP
6
7
8
110 OVAL STACKHEAD
10x4x6
10x6x6
12x6x6
12x6x7
12x6x8
14x6x8
113 FLAT 45 ANGLE
6
7
8
114 FLAT 90 ELBOW
6
7
8
115 VERTICAL 45 ANGLE
6
7
8
116 VERTICAL 90 ELBOW
6
7
8
124NC OVAL TO ROUND 90 BOOT - NO CRIMP
6
7
8
124R 90 REGISTER BOOT
4x10x6
4x12x7
127NC OVAL TO ROUND STRAIGHT BOOT - NO CRIMP
6
7
8
127R 4X10X6 STRAIGHT REGISTER BOOT
355 STRAIGHT OVAL REGISTER BOX
4x10x6
4x12x7
360 4X10X6 ANGLE OVAL REGISTER BOX
OVAL START COLLAR
6 in
7 in
WALL STACK
24 in Joint 2-1/4x10
24 in Joint 2-1/4x12
24 in Joint 2-1/4x14
24 in Joint 3-1/4x10
24 in Joint 3-1/4x12
24 in Joint 3-1/4x14
100 in Joint 2-1/4x12
100 in Joint 3-1/4x10
100 in Joint 3-1/4x12
100 in Joint 3-1/4x14
1031 3-1/4x STACKHEAD
10/6x10
12/6x12
14/6x14
1045 FLAT 45 ANGLE
2-1/4x10
2-1/4x12
3-1/4x12
3-1/4x14
1046 FLAT 90 ELBOW
2-1/4x10
2-1/4x12
2-1/4x14
3-1/4x10
3-1/4x12
3-1/4x14
1041 VERTICAL 45 ANGLE
2-1/4x10
2-1/4x12
3-1/4x10
3-1/4x12
3-1/4x14
1040 VERTICAL 90 ELBOW
2-1/4x10
2-1/4x12
3-1/4x10
3-1/4x12
3-1/4x14
1100 2-1/4x10 STRAIGHT COLLAR
1110 3-1/4x END CAP
10in
12in
14in

COMMERCIAL TAKE-OFFS

ATD AIR-TITE TAKEOFF w/DAMPER
4
5
6
7
8
9
10
12
14
16
18
20
ATDBM BELL-MOUTH TAKEOFF w/DAMPER
6/6x8
7/7x9
8/8x10
10/10x12
12/12x14
14/14x16
16/16x18
ATDRP ROUND PIPE TAKEOFF w/DAMPER
4
5
6
7
8
10
12
14
ATHE HIGH EFFICIENCY TAKEOFF
5/6x10
6/6x10
7/6x10
8/8x12
9/9x12
10/10x14
12/12x18
14/14x18
ATHEWD HIGH EFFICIENCY TAKEOFF w/DAMPER
5/6x10
6/6x10
7/6x10
8/8x12
9/9x12
10/10x14
12/12x18
14/14x18
ATT AIR-TITE PLAIN TAKEOFF
4
5
6
7
8
9
10
12
14
16
18
20
ATTBM AIR-TITE BELL-MOUTH TAKEOFF
6/6x8
7/7x9
8/8x10
10/10x12
12/12x14
14/14x16
16/16x18
ATTRP AIR-TITE ROUND PIPE TAKEOFF
4
5
6
7
8
9
10
12
14
ATTRP45 AIR-TITE 45 SADDLE TAKEOFF
6
8
12

Sheet Metal Takeoffs & Collars

122SC FIBERGLASS SNAP COLLAR
6
8
10
12
1051 FLAT COLLAR - CRIMPED
3
4
5
6
7
8
9
10
12
14
16
18
1150 LONG FLAT COLLAR
6
8
10
12
14
16
18
20
1149 LONG FLAT COLLAR W/DAMPER
5
6
7
8
10
12
14
16
1050 FLAT COLLAR - NO CRIMP
3
4
5
6
7
8
9
10
12
14
16
18
EP15 ROUND TO ROUND ADJUSTABLE TAKEOFF
6x5
7x6
8x7
9x8
HT15 7X6 ROUND TO ROUND HALF TAB TAKEOFF

Tees, Reducers & Accessories

1057 STORM COLLAR
3
4
5
6
7
8
10
12
14
207 90 QUICK TEE
3
4
5
6
7
208QY 45 QUICK Y
3
4
5
6
7
1066 ONE QUAD DAMPER
4
5
6
7
8
1067 TWO QUAD DAMPER
6
8
10
12
14
16
1064 ROUND END CAP
3
4
5
6
7
8
9
10
12
14
16
18
20
1065 DRAWBAND w/GEAR CLAMP
4
5
6
7
8
9
10
12
14
16
1062 TAPPERED 3 PIECE REDUCER
4x3
5x3
5x4
6x3
6x4
6x5
7x4
7x5
7x6
8x4
8x5
8x6
8x7
9x5
9x6
9x7
9x8
10x6
10x7
10x8
10x9
12x6
12x7
12x8
12x10
14x6
14x8
14x10
14x12
16x10
16x12
16x14
18x12
18x14
18x14
18x16
1063 SHORT 2 PIECE REDUCER
4x3
5x3
5x4
6x3
6x4
6x5
7x3
7x5
7x6
8x4
8x5
8x6
8x7
9x6
9x7
10x6
1060 FREE FLOW TEE
3x3x3
4x4x4
5x5x3
5x5x5
6x6x6
7x7x7
8x8x8
10x10x10
12x12x12
14x14x14
16x16x16
18x18x18
1061 Y BRANCH
4x3x3
4x4x4
6x4x4
6x6x6
8x6x6
10x8x8
12x10x10
1058 FLUE Y
4x3x3
4x4x3
4x4x4
5x4x3
5x4x4
5x5x3
5x5x4
6x4x3
6x4x4
6x5x3
6x5x4
6x6x3
6x6x4
6x6x6
7x6x3
7x6x4
8x6x6
1059 26GA TEE JOINT
3x3x3
4x4x4
5x5x3
5x5x5
6x6x3
6x6x6
7x7x7
8x8x8
9x9x9
10x10x10
12x12x12
14x14x14

VENTING

Broan Roof Cap, Black, Round Duct
  • Built-in backdraft damper and bird screen
  • Steel baked black enamel finish
634 8in
636 3in or 4in
F040CP Air Connector Class 0 - Flex Aluminum - 8 FT
  • Sturdy corrugated aluminum construction
  • One end crimped, compressed
  • GREENGUARD Level 4 highly microbial resistant
  • UL-listed air duct
3in
4in
5in
6in
7in
8in
10in
12in
1705 FRESH AIR INTAKE NO DAMPER
6
8
10
12
1706 GALV VENT HOOD
5
6
8
10
12
4in ALUMINUM PIPE
24 inch length
60 inch length
4in Aluminum Elbow
SVH ALUMINUM VENT HOOD
3in
4in
201VH 3-1/4x10 ALUMINUM WALL CAP
DVB Dryer Vent Box
  • DVB-350 (For Upward Exhaust Direction) DB-3D (For Downward Exhaust Direction)
  • 22 gauge aluminized steel weighing 4 pounds each
  • DVB-350 Top port measures 4-7/8" x 3-1/8" oval shape, DB-3D 4-1/8" slight oval
  • Distance from nailing flange to rear of box is 3-1/2" for both
  • DVB-350 Overall measurements: 21" h x 12 1/2" w x 4 3/8" deep, DB-3D 19" x 16-3/4" x 4-3/8"
  • DVB-350 Inside measures 9-1/2" wide x 18-1/4" tall, DB-3D 14" x 16"
  • ...
DB 350 Upflow
DB 3D Downflow
ALUMINUM ROOF CAP W/ DAMPER and SCREEN
239 4in
240 7in
241 10in
Louver Vent Hood - White
  • Louvered Wall vent white
  • Easy to install
  • Long lasting quality
  • Made in the USA
390WP 4in White w/tailpiece
391WP 4in White face only
391WP 6in White face only
Rotaire w/screen - Undereve Bath Fan Vent
  • Grille is designed for accepting all types of Flex Duct
  • All plastic construction
  • Offers the ideal properties for increased efficiency in all heating and air conditioning applications
  • 360 rotation (except 6in), easy installation and long term durability
  • Most often used as an undereve outlet for venting bath fans to the outside in housing applications
  • ...
3840WHW 4in White
3840WNW 4in Walnut
3860WHW 6in White (does not rotate)
SVHP 4in PLASTIC VENT HOOD
White
Brown

SPIRAL PIPE & FITTINGS

G-3® Fittings With Double-Lipped Gaskets

TCPG Tee
  • assembled tee with die-stamped or fabricated PSG
  • L = Ød3 + 6"
  • H = 1"
6
8
10
12
14
BSFG 45 Elbow
  • 3-piece gored, standing seam
  • gore locked and internally sealed
  • rolled edges
14
16
18
20
22
24
BSFG 90 Elbow
  • 5-piece gored, standing seam
  • gore locked and internally sealed
  • rolled edges
14
16
18
20
22
24
BSG 45 Elbow
  • die stamped
  • continuous stitch welded
  • rolled edges
4
6
8
10
12
BSG 90 Elbow
continuous stitch welded rolled edges galvanized steel only available in diameters 3"- 12"
4
6
8
10
12
DSG Damper
  • balancing damper for use in systems where a complete shut-off of air flow is not required
  • gasketed, shaft-mounted load-bearing bushing
  • integral shaft-blade assembly
  • 2” sheet metal insulation stand-off
  • locating blade quadrant w/damper position indicator
  • gasketed shaft penetrations to minimize leakage
  • full fitting body assembly with bead stop
  • 2" shaft extension available
  • ...
4
6
8
10
12
14
ESG End Cap
End cap for spiral duct
4
6
8
10
12
14
16
18
20
ILG Takeoff
  • installed on flat side of duct or plenum
  • available in diameters 3"- 60"
18
20
22
24
NPG Coupling
couplings are used for joining spiral ducts
4
6
8
10
12
14
16
18
20
22
24
PSG Saddle Tap
  • H = X + 1/2"(ØD)
  • pressed:
    • - radius entry
    • - limited to galvanized steel only
  • fabricated sizes listed below
    • - H = 1"
4 on 6 pipe
6 on 6 pipe
6 on 8 pipe
6 on 10 pipe
6 on 12 pipe
6 on 18/16/14 pipe
8 on 8 pipe
8 on 10 pipe
8 on 12 pipe
8 on 16/14 pipe
8 on 20 pipe
10 on 10 pipe
10 on 12 pipe
10 on 14 pipe
10 on 16 pipe
10 on 20/18/16 pipe
12 on 12 pipe
12 on 14 pipe
12 on 16 pipe
12 on 22/20/18 pipe
14 on 14 pipe
14 on 16 pipe
14 on 18 pipe
16 on 16 pipe
RCG Reducer
  • die stamped concentric reducers
  • sizes greater than 14″ will not be stamped
6x4
8x6
10x6
10x8
12x8
12x10
14x8
14x10
14x12
16x8
16x10
16x12
16x14
18x14
18x16
BFG 90 Elbow
  • 4-piece gored, standing seam
  • gore locked and internally sealed
  • available in diameters 14"- 48"
  • note: BF/G 90 elbows 50-inch diameter and larger will be supplied as two BF/G 45º elbows and an MF coupling
14
16
18
20
22
24
BG 90 Elbow
  • die stamped
  • continuous stitch welded
  • rolled edges • galvanized steel only
  • available in diameters 3"- 12"
  • note: 11" diameter is fabricated
6
8
10
12
ILRG Takeoff
  • stamped radiused bellmouth take-off
  • available in 4"-16" (not including 11")
  • installed on flat side of duct or plenum
4
6
8
10
12
14
16

Pipe and G-0 Nongasketed Fittings

SR 10FT GALVANIZED SPIRAL PIPE
  • spiral lock seam duct
  • SMACNA’s RL-1 spiral seam
  • evenly spaced integral seam locking feature
  • multiple corrugations on all duct 8" diameter and larger
3
4
5
6
7
8
10
12
14
16
18
20
22
24
BS 45 Elbow
  • continuous stitch welded
  • die stamped
  • rolled edges
  • galvanized steel only
3
4
5
6
7
8
9
10
12
BS 90 Elbow
  • continuous stitch welded
  • die stamped
  • rolled edges
  • galvanized steel only
3
4
5
6
7
8
9
10
12
BSF 45 Elbow
  • 3-piece gored, standing seam
  • gore locked and internally sealed
3
4
5
6
7
8
9
10
12
BSF 90 Elbow
  • 5-piece gored, standing seam
  • gore locked and internally sealed
3
4
5
6
7
8
9
10
12
RC Reducer
  • die stamped concentric reducers
  • sizes greater than 14″ will not be stamped
6x4
8x6
10x8
12x10
14x12
16x14
RCL Reducer
  • fabricated concentric reducer
  • L1 = Ød1 - Ød2 (minimum 4")
18x16
20x18
22x20
24x22

COMMERCIAL TAKEOFFS

ATHEWD HIGH EFFICIENCY TAKEOFF w/DAMPER
5/6x10
6/6x10
7/6x10
8/8x12
9/9x12
10/10x14
12/12x18
14/14x18

TYPE B ROUND VENT

C - Metal Cap (14-30 inch)
  • Barriers provided in cap opening spaced less than 1" are designed to resist entry of birds
  • Snap-locks onto pipe
12in
14in
16in
RAA Adapter - Male
  • Adapts thicker wall brands of B vent to Hart&Cooley vent (theirs to ours)
4in
5in
REA45 45 Degree Adjustable Elbow
.
7in
8in
10in
12in
14in (R45)
REA60 60/45 Degree Adjustable Elbow
3in
4in
5in
6in
REA90 90 Degree Adjustable Elbow
.
3in
4in
5in
6in
7in
8in
RF Adjustable Roof Flashing 0-6 /12 Pitch
.
3in
4in
5in
6in
7in
8in
10in
12in
14in
RFA Adjustable Roof Flashing 6/12-12 /12 Pitch
Available in 3" through 8".
3in
4in
5in
6in
7in
8in
RGS Gripper Support 3-6 inch
  • Supports 30 feet of pipe
  • Acts as a firestop
  • 7", 8" and 10" not UL-listed
3in
4in
5in
6in
RHW Cap (3-6 inch)
  • Exceptional performance in windy conditions
  • Designed to resist nesting birds
3in
4in
5in
6in
RM Cap (7-12 inch)
  • Barriers provided in cap opening spaced less than 1" are designed to resist entry of birds
7in
8in
10in
12in
RN Increaser
4to5in
4to6in
8to10in
RP Round Pipe 12in Length
  • 3" to 12" pipe and fitting couplers overlap 13/8" when joined together; therefore, assembled length is 13/8" less than listed length
  • The allowable minimum clearance to combustibles is 1", except for 4RPX on which clearance is provided by locking band on pipe only when installed in a 2 x 6 stud wall
  • Outside Diameter (OD) Sizes 3" through 6" is size plus 1/2", Sizes 7" through 12" is size plus 1"
  • A full set of installation instructions are supplied with caps and supports
  • ...
3in
4in
5in
6in
7in
8in
RP Round Pipe 18in Length
  • 3" to 12" pipe and fitting couplers overlap 13/8" when joined together; therefore, assembled length is 13/8" less than listed length
  • The allowable minimum clearance to combustibles is 1", except for 4RPX on which clearance is provided by locking band on pipe only when installed in a 2 x 6 stud wall
  • Outside Diameter (OD) Sizes 3" through 6" is size plus 1/2", Sizes 7" through 12" is size plus 1"
  • A full set of installation instructions are supplied with caps and supports
  • ...
3in
4in
5in
6in
7in
8in
10in
12in
RP Round Pipe 24in Length
  • 3" to 12" pipe and fitting couplers overlap 13/8" when joined together; therefore, assembled length is 13/8" less than listed length
  • The allowable minimum clearance to combustibles is 1", except for 4RPX on which clearance is provided by locking band on pipe only when installed in a 2 x 6 stud wall
  • Outside Diameter (OD) Sizes 3" through 6" is size plus 1/2", Sizes 7" through 12" is size plus 1"
  • A full set of installation instructions are supplied with caps and supports
  • ...
3in
4in
5in
6in
7in
8in
10in
12in
14in
16in
RP Round Pipe 3ft Length
  • 3" to 12" pipe and fitting couplers overlap 13/8" when joined together; therefore, assembled length is 13/8" less than listed length
  • The allowable minimum clearance to combustibles is 1", except for 4RPX on which clearance is provided by locking band on pipe only when installed in a 2 x 6 stud wall
  • Outside Diameter (OD) Sizes 3" through 6" is size plus 1/2", Sizes 7" through 12" is size plus 1"
  • A full set of installation instructions are supplied with caps and supports
  • ...
3in
4in
5in
6in
7in
8in
10in
12in
14in
16in
RP Round Pipe 5ft Length
  • 3" to 12" pipe and fitting couplers overlap 13/8" when joined together; therefore, assembled length is 13/8" less than listed length
  • The allowable minimum clearance to combustibles is 1", except for 4RPX on which clearance is provided by locking band on pipe only when installed in a 2 x 6 stud wall
  • Outside Diameter (OD) Sizes 3" through 6" is size plus 1/2", Sizes 7" through 12" is size plus 1"
  • A full set of installation instructions are supplied with caps and supports
  • ...
3in
4in
5in
6in
7in
8in
RPA Adjustable Length Pipe
.
3x12in
4x12in
5x12in
6x12in
8x18in
10x18in
12x18in
RS Storm Collar
7 - 12 inch are adjustable
3in
4in
5in
6in
7in
8in
10in
12in
RSA Support Assembly (3-12in)
  • Supports 30 feet of pipe
  • Acts as a firestop
3in
4in
5in
6in
7in
8in
SC Adjustable Storm Collar (14-30in)
Designed to be snug around vent pipe for a weather-tight fit.
14in
16in
18in
20in
RT Tee
.
3x3x3
5x5x5
6x6x6
6x6x3
7x7x7
8x8x8
10x10x10
12x12x12
RTF Tall Cone Roof Flashing
3in
4in
5in
6in
7in
8in
10in
12in
14in
16in
18in
RWT Wall Thimble
  • Provides necessary clearance to combustibles
  • Sleeve is adjustable from 3" to 6"
4in
5in
6in
7in
8in

TOOLS

13/16" Hand Notcher
The N1R Hand Notcher makes a clean 30° “V” shaped cut in 24-gauge (0.
14" Straight Aluminum Snip
Sleek styling, easy blade replacement and larger handles make the Andy™ Snip more versatile.
18" Divider
Catalog # Description Length in.
3" Hand Seamer
Malco Hand Seamers, with forged steel jaws, are the premier choice for bending, folding, flattening and straightening sheet metal edges or safely gripping and moving sheet metal around the job site.
3" Offset Hand Seamer
Malco Hand Seamers, with forged steel jaws, are the premier choice for bending, folding, flattening and straightening sheet metal edges or safely gripping and moving sheet metal around the job site.
5-Blade Crimper
Use the Malco C5R Crimper to downsize stove pipe and round metal duct to create a male connection for joining sections.
Auto Tie Tension Tool
For continuous use on-the-job.
Cushioned Gripped Serrated Duct Knife DK6S
For cutting flexible fiberglass wool duct and ductboard.
Cutter Bit for HC1 or HC2
Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal.
Duct Holder
Like an extra pair of hands, this job-site helper holds ductwork in place with clamps and a chain during installation until permanently secured.
Flex Duct Shear
Cuts insulated flexible round duct and also cuts the duct liner’s wire rib coil.
Folding Tool
Folding Tool seams are formed from two steel halves, permanently joined together.
24F 24" Folding Tool
12F 12" Folding Tool
18F 18" Folding Tool
Gripped Tie Tensioning Tool
These rugged lever action tie tools feature a unique notched gripper.
Hole Cutter
Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal.
HC1
HC2
Hole Cutter Pivot Pin Set for HC-1
Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal.
Lenox Metal Cutting Reciprocating Saw Blades (5 pack)
POWER BLAST TECHNOLOGY™ INCREASES BLADE LIFE High speed blasting along the cutting edge strengthens the blade to reduce breaks and increase durability LONG BLADE LIFE & INCREASED VERSATILITY Patented T2™ Technology reduces cutting forces on each tooth and optimizes chip removal to allow efficient cutting in the widest range of materials ADVANCED METAL CUTTING TOOTHFORMS Patented metal cutt...
618R 6 x 3/4 x .035 TPI 18
624R 6 x 3/4 x .35 TPI 24
818R 8 x 3/4 x .35 TPI 18
Lenox Wood Bi-Metal Reciprocating Saw Blades (5 pack)
POWER BLAST TECHNOLOGY™ INCREASE BLADE LIFE High speed blasting along the cutting edge strengthens the blade to reduce breaks and increase durability LONGER BLADE LIFE & INCREASED VERSATILITY Patented T2™ Technology reduces cutting force on each tooth and optimizes chip removal to allow efficient cutting in the widest range of materials OPTIMIZED TOOTHFORMS FOR WOOD CUTTING Patented design...
656R 6 x 3/4 x .50 TPI 6
956R 9 x 3/4 x .50 TPI 6
MW-M1200 Straight Cut Replacement Blade Snip
  • Cuts straight and wide curves
  • Use in either hand
  • 3-1/2" length of cut and replaceable blades
  • Meets ASME Standard B107:500-2010(B107:16)
Offset Duct Stretcher
Use the Duct Stretcher to hold duct in place with one hand while slipping drive cleat in place with other hand.
Scratch Awl
Use to scribe lines on metal, plastic and a variety of other materials.
A1, Large Grip 7/32"
A2, Large Grip 1/4"
A3, Large Grip 3/8"
A20, Regular Grip 1/4"
Scriber
Measure, mark and scribe trim lines on sheet metal in one easy operation.
Snap Lock Punch
Create locking tabs for resizing rectangular metal duct at the job site.
Tinknocker Tool
Tinknocker tool is used to help make the installation of drive cleats simpler than ever before!
  • Tinknocker Tool makes driving cleats faster than ever before
  • Attaches to all SDS shanks
  • Decreases muscle & shoulder fatigue and increases your productivity
Turbo Crimper
Every HVAC sheet metal worker needs a TURBO CRIMPER® TurboCrimper IMPACT The Malco TurboCrimper IMPACT is a simple, compact accessory that works exclusively with the power assistance of impact driver technology to safely and efficiently crimp 30 to 24 gauge (0.
Turbo Shear
The time-saving TURBOSHEAR Model No.
Turbo Shear, Heavy Duty
Making your power drill a powerful metal-cutting shear is now a more attractive idea than ever before! This well tailored attachment quickly inserts into the chuck of a corded or cordless drill to make fast straight, curved or square cuts in most common sheet metals.
Aviation Snips - Regular Models
IMPROVED MAX2000 SNIPS FIT ANY HAND WITHOUT SACRIFICING CUT.
M2001 Left Cut Red Handle
M2002 Right Cut Green Handle
Aviation Snips - Offset
  • Cuts straight and tight left/right curves
  • Easiest used in right hand
  • Bottom blade serrated
  • Meets ASME Standard B107-500-2010(B107-16)
  • Nominal Length: 9-3/4"
  • Cut Length: 1-1/4"
  • Cutting Capacity (CR/SS): 18/22
M2007 Right Cut Green Handle
M2006 Left Cut Red Handle
Bulldog Snip
Molded thermoplastic grips, narrower grip opening accommodates large or small hands to maximize the powerful leverage of compound handle to head linkage, ambidextrous one hand operation latch, and a fast adjusting, long life pivot bolt with nylon locking nut and pressure washer.
Double Cut Snips
The Malco M2004 is a Metal Double Cut Snips.
SSES Stainless Edge Scribe
The stainless steel edge scribe provides a simple and easy marking of metal sheets
MW-HP2 4 Tip Manual Rivet Gun
  • 4 interchangeable nosepieces for 3/32", 1/8", 5/32", and 3/16"dia aluminum, copper, steel, or stainless steel
  • Heavy-duty model
  • Molded grips comfort user’s hand
323W Circular Steel Gauge
  • Heavy steel circular gauge for determining steel thickness from 0 through 36 gauge
  • Manufactured with zinc plated hardened steel and comes with its own protective storage case
DDTH18 18oz Tinner's Hammer
  • It is available in one convenient weight
  • This 18 ounce hammer is made of one piece polished solid steel with an industrial strength rubber grip fastened securely in place
HM16 16 ounce Hickory Mallet 2-1/2" inch face diameter
When fabricating ductwork, a mallet is often necessary to align joints.
Skeleton Caulking Gun
Heavy-duty professional quality skeleton caulking gun with “no drip” feature, spout cutter, seal puncture tool and ladder hook for hanging when not in use.
DC Hex Shank Drill Chuck
16016 DCLX 6in x 5/16
16018 DC 1-3/4in x 1/4
16019 DC 1-3/4in x 5/16
16009 DCL 2-5/8in x 1/4
16009 DCL 2-5/8in x 5/16
16015 DCLX 6in x 1/4
TD Super T Drill Bit (10pk)
  • Fast Cutting - Fast Starting 135º split point starts the hole where you place it; drill does not “walk”, mar metal, or waste time
  • Long Wearing - Extra Hard Specially hardened high speed steel makes “Super T” Drill Bits harder and longer wearing than others; This same steel/processing combination allows bits to withstand the stress of tortional twisting
  • Heavy Web - Reduces Breakage, web is the portion which is solid steel from point to shank; “Super- T” has heavier web than ordinary bits; This means more flexibility, less breakage
  • ...
24004 1/8
5/32
3/16
7/32
24013 1/4
TED Twin End Super T Drill Bit (10pk)
  • Fast Cutting - Fast Starting 135º split point starts the hole where you place it; drill does not “walk”, mar metal, or waste time
  • Long Wearing - Extra Hard Specially hardened high speed steel makes “Super T” Drill Bits harder and longer wearing than others; this same steel/processing combination allows bits to withstand the stress of tortional twisting
  • Heavy Web - Reduces Breakage, web is the portion which is solid steel from point to shank; “Super- T” has heavier web than ordinary bits; This means more flexibility, less breakage
  • ...
24015 1/8
24016 #30
Hensler's Bender
The Henslers Bender is a quality sheet metal hand brake which was designed with the user in mind; created over 50 years ago by Charlie Hensler, this tool is great for any one in the field that requires the bending of sheet metal; this is a incredible tool if you are in the trade of roofing or heating and air conditioning; Description: Lightweight tool bends 24 to 26 gauge metal up to 135° Makes t...
POT Pittsburgh Lock Opening Tool
FEATURES: • Made of durable 30% glass filled nylon for strength and long life • Wide face reduces marring exposed ductwork along the leading edge of the female side of the Pittsburgh lock • Comfortable, ergonomic grip • Easily ground down to a narrower profile to fit on tighter radius elbow seams • Orange color is highly visible, less time searching for the tool you need • Tapered lead...
DDIV18R 18in Divider
Heavy duty plated steel legs are angled inward to allow the points to come very close
DDHC12 12in Hole Cutter
  • Saves time! Especially when several same size holes are being cut
  • Cuts holes up to 12" in diameter!
  • Will cut light gauge metal, aluminum, plastics, formica!
  • Replaceable three fluted cutting bit!
DDHC-12RB Replacement Bit For Hole Cutter
The replacement bit is a three fluted cutting bit.

ACCESSORIES

Sealants

SureGrip 404 Indoor Application Fiber Free Solvent Base Duct Sealant
Sure-Grip 404 is a fiber-free, solvent based, synthetic rubber duct sealant.
SG 404 - 1 Gallon
SG 404 - 11oz Tubes
BOSS® 125 Multi-Seal® Building Construction Sealant (Case-12)
  • VOC compliant in all 50 States
  • Paintable with most latex paint
  • Non-yellowing and non-staining
  • Paintable under an hour
  • Bonds to wet, damp surfaces
Clear
White
Aluminum
Almond
Limestone / Cityscape
Redwood Tan / Colonial Red
Special Bronze / Dark Bronze
Medium Bronze
Black
Stone / Sandstone
Off White / Stone White
Slate Gray
Mansard Brown
Hunter Green / Hartford Green
BOSS® 136 Fireblock / Draftstop Sealant
  • A one-part, noncombustible filler caulk
  • The ideal product for residential construction and meets all sections of the newly adopted International Residential Building Code I
  • Adhesion properties are superior to other products on the market - it literally sticks to the most common construction materials and is semi-flexible
  • Interior use only and is particularly suited for sealing walls and floors which have been penetrated by pipes, conduits, or electrical cables in all types of construction and for filling interior voids around HVAC, plumbing, and framing
  • Application is with a standard caulk gun or trowel, and clean up is with water
  • Meets and exceeds the specifications for ASTM E-136 and conforms to all National Building Codes, including BOCA, CABO, SBCCI, ICBO, NFPA and the 2003 International Building Codes
  • It is the most versatile firestop product available in today's marketplace
  • ...
BOSS® 312 RTV HVAC/R Silicone Sealant
  • Permanently flexible
  • Adheres to glass, wood, metal, porcelain, ceramic tile, painted surfaces and rubber
  • May be applied in sub-zero weather without loss of extrusion or physical property characteristics
  • Meets NSF Standard 51 & FDA/USDA requirements for use in operations under Meat and Poultry Inspection Program
  • Insulates thermally & electrically
  • Waterproof & Weatherproof seal
  • ...
Clear
White
Aluminum
BOSS® 326 Hi-Temp Red Silicone Sealant
  • Provides a protective coating where parts must perform at temperatures up to 500°F
  • Used in critical bonding, sealing, potting, and encapsulating applications
  • Paste grade acetoxy silicone
  • Cures to a tough rubbery solid at room temperature
  • Meets NSF Standard 51, and FDA/USDA requirements for use in establishments operating under Fedral Meat and Poultry Inspection Program
  • ...
BOSS® 333 Expanding Foam Sealant
  • Easy-to-use, multi-purpose urethane foam
  • Unlike ordinary sealants, it expands three times its original volume
  • Adheres to all building materials except Teflon, silicone and polyethylene
  • Seals by expanding into gaps, cracks and crevices
  • Uses include insulating, sealing and filling gaps around pipes, plumbing fixtures, ductwork and foundations
  • UL Classified
  • ...
BOSS® 334 Window & Door Minimal Expanding Foam
  • AAMA 812-04 Approved to not bow window and door frames
  • Excellent adhesion on most substrates (except PTFE, PE and PP)
  • High thermal and accoustical insulation
  • Excellent mounting capacities
  • Excellent stability (no shrink or post expansion)
  • Very precise application due to the foam gun system
334-24 Sealant
M0051 Gun
BOSS® 335 Gun Foam Cleaner
  • Specially developed to clean the PU foam applicator guns
  • A correct cleaning of the gun and the proper use of the product will ensure an optimal function and prevent blockage of the applicator gun
  • Suited for cleaning of the valve and spray nozzle of PU foam cannisters and removing uncured PU foam
BOSS® 348 Multi Purpose Construction Adhesive
  • VOC Compliant
  • Fast grab, easy to use
  • Bridges minor framing irregularities
  • Easy clean up
  • Reduces sound transmission, Unaffected by moisture
  • Drip resistant, Reduces nailing
BOSS® 812 Fire Block Foam
  • Will adhere to almost any substrate
  • Can be used to seal around copper, PVC pipes conduits and large spaces left after the installation of waste pipes, ducting, etc.
BOSS® 813 Expanding Firestop Foam - 12 ounce
  • Will adhere to almost any substrate
  • Installed in seconds, reducing labor cost by up to 90%
  • Ideal for hotels, hospitals, prisons, condominiums, single and two family homes
  • Paintable
  • Can be used on vertical or horizontal applications
  • Excellent acoustic and thermal insulation
  • Unaffected by moisture or humidity after curing
  • CFC Free
  • ...
BOSS® 816 Intumescent Firestop Sealant
  • Bonds quickly with excellent adhesion
  • Mildew Resistant
  • Remains flexible
  • VOC compliant
  • Excellent freeze / thaw properties
  • Safe to use and handle
  • Water based and paintable
  • It has been tested to the following specifications: UL 1479 (ASTM E-814), UL 2079 (ASTM E-1966), ASTM E-84 (0-flame, 0-smoke), ASTM E-90 (STC 53)
  • ...
BOSS® 893 Boss Biggies Dual Side Abrasive Wipes
  • Pre-moistened
  • Textured weave for added scrubbing power
  • Contains an advanced formula and special dual-sided towel that removes:
  • Acrylic - Enamel - Epoxy - Rubber Cement - Oil - Silicone
  • Grease - Glue - Ink - Poly Foam and much more .

Tape

1500 Silver Cloth Duct Tape 2" x 60 yards
A Venture Tape Unlike Any Other A high quality polyethylene cloth tape coated with a natural rubber pressure sensitive adhesive system, our 3M™ Venture Tape™ Cloth Duct Tape 1500 has very high tack, high peel and adheres to corners and irregular surfaces.
1525CW FSK Tape 3" x 50 yards
Vapor seal Attributes Adhesive Type‎ ‎ Acrylic Brand‎ ‎ Venture Tape Color‎ ‎ Aluminum Consumer Label‎ ‎ No Elongation‎ ‎ 2 Percent Length‎ ‎ 50 Linear Yard Product Form‎ ‎ Roll Shelf Life‎ ‎ 12 months from date of shipment Tensile Strength‎ ‎ 40 lb/in Width‎ ‎ 2.
1581A UL Foil Tape UL181A-P Printed 2.5" x 60 yards
Vapor seal on rigid duct board Attributes Adhesive Type‎ ‎ Acrylic Backing Material‎ ‎ Aluminum Foil Brand‎ ‎ Venture Tape Color‎ ‎ Aluminum Consumer Label‎ ‎ No Elongation‎ ‎ 10 Percent Length‎ ‎ 60 Linear Yard, Product Form‎ ‎ Roll Shelf Life‎ ‎ 12 months from date of shipment Tensile Strength‎ ‎ 27 lb/in Width‎ ‎ 2.
1599B Silver Flex Duct Tape UL181B-FX 2" x 120 yards
Use as a flexible duct closure tape Attributes Adhesive Type‎ ‎ Acrylic Backing Material‎ ‎ Polypropylene Brand‎ ‎ Venture Tape Color‎ ‎ Black,‎ Silver Consumer Label‎ ‎ No Elongation‎ ‎ 130 Percent Length‎ ‎ 119.
3520CW Foil Tape 3" x 50 yards
Vapor seal for fibrous and sheet metal ducts as well as FSK systems Attributes Adhesive Type‎ ‎ Acrylic Backing Material‎ ‎ Aluminum Foil Brand‎ ‎ Venture Tape Color‎ ‎ Aluminum Consumer Label‎ ‎ No Elongation‎ ‎ 4 Percent Length‎ ‎ 50 Linear Yard Product Form‎ ‎ Roll Shelf Life‎ ‎ 12 months from date of shipment Tensile Strength‎ ‎ 21 lb/in Width‎ ‎ 3...
AFG-1404-181BFX Silver Foil 3"x100' Indoor/Outdoor Foil Grip Tape
Foil-Grip 1404-181-BFX is a UL 181B-FX listed pressures sensitive rolled mastic sealant.

HARDWARE

1-5/8x1-5/8 10ft Strut
UST001 Galvanized
UST003 Green
732 Pipe Support
Galvanized sheet metal pipe support
BC38NS 3/8 Small Mouth Beam Clamp w/ Lock Nut (Box of 100)
Small mouth 3/8 in: max top load= 500lbs max bottom load=250lbs
Crimp Multi-Purpose Anchors
Crimp anchor is an easy-to-install expansion anchor for use in concrete and grout-filled block; The pre-formed curvature along the shaft creates an expansion mechanism that secures the anchor in place and eliminates the need for a secondary tightening procedure; This speeds up anchor installation and reduces the overall cost.
CD25118T 1/4 Tie Wire 100-pk
DOMDOC Dyn-O-Claw (Box of 250)
  • Ductwork is often reinforced with conduit to minimize movement caused by positive or negative pressures
  • Dyn-O-Claw is designed to join the cross section of conduits to immobilize them which further strengthens the duct
  • Dyn-O-Claw also eliminates any vibration or rattling sound of crossing conduits
  • Dyn-O-Claws create an effective duct strengthening system and are easier and faster than other alternatives such as ties or welding
  • ...
21088 1/2 inch
21089 3/4 inch
Drop-In Anchor Hand-Setting Tool For DIA
Use the drop-in anchor setting tool to facilitate placement of the Simpson Strong-Tie Drop-In anchor (DIA).
DIAST25 1/4 Setting Tool 10-pk
DIAST37 3/8 Setting Tool 10-pk
DIAST50 1/2 Setting Tool 10-pk
Drop-In Anchor Hand-Setting Tool For DIAB
Hand-setting tool designed for use with the new Simpson Strong-Tie Drop-In anchor (DIAB), ensuring fast, easy and economical installation.
DIABST37 3/8" Manual Setting Tool
DIABST37-SDS Power Setting Tool
Drop-In Internally Threaded Anchor Lipped 3/8"
Simpson Strong-Tie introduces a new, redesigned Drop-In anchor (DIAB) that provides easier installation into base materials.
Horizontal Steel Rod Hanger Threaded Rod Anchor System
Size: 12-20x1-1/2", 3/8" rod Price is for one box (25 pieces) The Simpson Strong-Tie® steel rod hanger is a one-piece fastening system for suspending 1/4" and 3/8" threaded rod.
Nailon™ Pin Drive Anchors - Zinc
  • Zinc Nailon™ anchors are low cost anchors for light-duty applications under static loads
  • Zinc Nailon anchor: Available with carbon and stainless-steel pins
  • The pin and head configuration make this anchor tamper resistant
ZN25100 1/4x1 Zinc (100pk)
ZN25114 1/4x1-1/4 Zinc (100pk)
ZN25112 1/4x1-1/2 Zinc (100pk)
PDPA Drive Pins 100-pk
  • For A36 and A572 Grade 50 structural steel (red strip load recommended)
  • 157 diameter for greater compressive strength
  • Manufactured with tight tolerances for superior performance
62K 5/8 LV Knurled
75 3/4 LV
PHS-100 Plastic Hanging Strap - 3/4in x 100ft
100' Plastic Hanger Strap, 10pcs/case, 1/8" hole every 3/4", Durable, non-abrasive available for a wide range of suspension needs.
PSLV4 Threaded Studs 3/4x1-1/4
  • The fasteners shall not be driven until the concrete has reached the designated compressive strength; minimum concrete thickness is three times the fastener embedment into the concrete
  • The allowable tension values are for the fastener only; connected members must be investigated separately in accordance with accepted design criteria
  • Metal deck must be minimum 20 gauge
  • The fasteners shall be installed 1-1/2 inches from the edge of flute
  • ...
SDS-PLUS® Drill Bits
For Concrete & Masonry SDS-Plus bits use an asymmetrical-parabolic flute for efficient energy transmission and dust removal Our carbide-tipped drill bits are premium quality, professional-grade tools manufactured in Germany to the highest industry standards for Simpson Strong-Tie®.
01807H 3/16x7
01804 3/16x4-1/4
01806 3/16x6-1/4
02504 1/4x4-1/4
02506 1/4x6-1/4
03706 3/8x6-1/4
05006 1/2x6-1/4
01505H Titen Hex 5/32x5
01805H Titen Hex 3/16x5
SDS-PLUS® Fixed- Depth Drill Bit
This fixed-depth SDS-plus® shank drill bit properly prepares the anchor site for the Simpson Strong-Tie® DIAS Short Drop-In in normal-weight, sand-lightweight and hollow-core concrete.
SFC18 FLANGE CLAMP SIDE MOUNTED (100 pack)
  • Black - Spring Steel
  • Zinc Phosphate & Oil
  • 1/4" - 1.
Strong‑Tie® Powder Loads - .27 Caliber Plastic - 10-Shot Strip Loads
Simpson Strong-Tie® P27SL .
Green Level 3
Yellow Level 4
Red Level 5
Threaded Rod Hanger - THDB37158RH 3/8 x 1 5/8 (50 / per box)
Size: 3/8 x 1 5/8 The Titen HD® threaded rod hanger is a high-strength screw anchor designed to suspend threaded rod from concrete slabs and beams or concrete over metal in order to hang pipes, cable trays and HVAC equipment.
Titen® Hex Head Concrete and Masonry Screws (100 Pack)
With patented undercutting threads that make installation easier and increase load capacity, the Titen® 2 concrete and masonry screw is ideal for attaching all types of components to concrete and masonry.
TTN18114H 1/8x1-1/4
TTN2-25114H 1/4x1-1/4
TTN2-25234H 1/4x2-3/4
TTN2-25134H 1/4x1-3/4
Vertical Steel Rod Hanger Threaded Rod Anchor System
Size: 1/4x2", 3/8" rod Price is for one box (25 pieces) The Simpson Strong-Tie® steel rod hanger is a one-piece fastening system for suspending 1/4" and 3/8" threaded rod.
Wood Rod Hanger Nut Driver
Custom-matched nut driver sets the wood rod hanger to the optimal depth.
Wood Rod Hanger Threaded Rod Anchor System
Simpson Strong-Tie’s wood rod hanger is a one-piece fastening system for suspending 1/4" or 3/8" threaded rod.
Vertical Wood Hanger RWV37200
Horizontal Wood Hanger RWH37200
HS 1in x 10ft Hanging Strap
13271 18GA
13272 22GA
ANGLE IRON 2inX2inX8ft
18 GA Hanging Wire 5#
  • 18 gauge galvanized
  • 830 feet
871 Ceiling Plate Collar
Galvanized sheet metal ceiling plate collar.
6in
8in
BASSET BRACKET A1 12 to 19in
Pro Pounder, Heavy Duty Tip Self-Nailing
BASSET SQUARE DUCT HANGER (100 per box)
  • Square duct hangers are a duct supporting bracket that screws into the joist at the top of the bracket
  • Square duct hangers have two points of duct support
  • First is an extension at the bottom of the bracket where the duct may rest
  • Second are two different hole locations for attachment screws
100 per box
8in
9in
100ft x 1in 26GA GALV BAND IRON
Galvanized Hanger Strap
Black Claw 1/8 - 1/4 Strap Hanger
  • Side Mount Flange Clamp with Right Angle Strap Hanger, Fits 1/8 to 1/4" Flange, Suspends Strap up to 1" Wide, Spring Steel
  • Side Mount Flange Clamp with Parallel Strap Hanger, Fits 1/8 to 1/4" Flange, Suspends Strap up to 1" Wide, Spring Steel
Parallel
Right Angle
Simpson Strong-Tie® RPS Strap Ties
  • Simpson Strong-Tie RPS 16 gauge Retro Plate Strap
  • RPS meets IBC, IRC and City of LA code requirements for HVAC and pipes in walls
RPS 22 1-1/2x22-5/16
RPS 18 1-1/2x18-5/16
Dyn-O-Mate Threaded Rod Accessories
Threaded Rod Accessories consisting of flat & fender washers, hex nuts, bolts and rod couplers; These accessories work in conjunction with Duro Dyne Threaded Rod to create a secure system for hanging ductwork and equipment.
21060 DOMNB38 3/8 Nut & Bolt Set (125 Bag)
21067 HN38C 3/8-16 Nut (100 Box)
21129 STRC38C 3/8 Rod Coupling (100 Box)
21141 FW38C 3/8 Flat Washer (100 Box)
TR3810ZP 3/8in x 10ft Threaded Rod - Zinc Plated
Hanging ductwork, equipment, wiring trays or other building components requires secure structural assemblies; These assemblies are comprised of support members attached to building anchor points with fasteners; The support members are often lengths of strut or angle iron; The fastener frequently is threaded rod combined with washers and nuts.

CHIMNEY

Air Jet Chimney Housing
  • Contents
    • Stainless Steel Cap (unpainted)
    • Painted Side Panels (4)
    • Flashing (2-piece set)
    • 18" Telescoping Aluminum Connector
    • 7-inch to 5 inch Reducer
  • For gas fueled appliances
  • Galvanized and stainless steel and aluminum components
  • ...
GHL36R 17x17x36 Brick Red
GHL36W 17x17x36 Brick White
GHL48R 17x17x48 Brick Red
GHL48W 17x17x48 Brick White
ALK — Aluminum Chimney Liner Kit
  • Kits include flexible length, round top,flashing, mortar guard
  • Standard kit lengths of 15', 25' and 35'
  • Available in 3", 4", 5", 6", 7" and 8" diameters in both kits and 10' extensions
  • 10' insulated sleeve has tough polyethylene exterior (sold separately)
  • Extension kit includes Flexi-Liner with attached connector and fastener package.
25ft x 4in
25ft x 5in
25ft x 5-1/2in
25ft x 6in
25ft x 7in
35ft x 4in
35ft x 5in
35ft x 5-1/2in
35ft x 6in
35ft x 7in
24in JT BLACK STOVE PIPE
6
8
6in BLACK 90 ELBOW
1070 CHIMNEY CAP
4
6
7
8
10
12
14
3ft Stainless Steel Pipe - Hammer Lock
6
8
10
Stainless Steel Elbow
6
8
10
12
Versa Cap® Flue and Hot Stack Caps
  • Non-clogging, positive draft design
  • For chimney, flue or hot stack installation
  • Clamp fitting adjustable for all standard sizes
  • Aluminum
  • UL listed
6-3050 3 to 5in
6-5070 5 to 7in
6-7090 7 to 9in
6-9011 9 to 11in
6-1200 12 to 14in

HVAC MULTI-PLUS DUAL BRAND V-BELTS

V-BELTS "3L" SECTION 0.38" TOP WIDTH x 0.22" THICKNESS x 40° ANGLE
3L180
V-BELTS "3VX" SECTION 0.38" TOP WIDTH x 0.31" THICK x 38° ANGLE
3VX850
3VX500
V-BELTS "A" SECTION 0.5" TOP WIDTH x 0.31" THICKNESS x 40° ANGLE
A20 (4L220)
A21 (4L230)
A22 (4L240)
A23 (4L250)
A24 (4L260)
A25 (4L270)
A26 (4L280)
A27 (4L290)
A28 (4L300)
A29 (4L310)
A31 (4L330)
A32 (4L340)
A33 (4L350)
A34 (4L360)
A35 (4L370)
A36 (4L380)
A37 (4L390)
A38 (4L400)
A39 (4L410)
A40 (4L420)
A41 (4L430)
A42 (4L440)
A43 (4L450)
A44 (4L460)
A45 (4L470)
A46 (4L480)
A47 (4L490)
A48 (4L500)
A49 (4L510)
A50 (4L520)
A51 (AL530)
A52 (4L540)
A53 (4L550)
A54 (4L560)
A55 (4L570)
A56 (4L580)
A57 (4L590)
A58 (4L600)
A60 (4L620)
A62 (4L640)
A64 (4L660)
V-BELTS "ACCU-LINK" SECTION
A-LINK-5
B-LINK-6
V-BELTS "AX" SECTION 0.5" TOP WIDTH x 0.31" THICK x 40° ANGLE
AX32
AX33
AX35
AX46
V-BELTS "B" SECTION 0.66" TOP WIDTH x 0.41" THICKNESS x 40° ANGLE
B36 (5L390)
B38 (5L410)
B40 (5L430)
B42 (5L450)
B43 (5L460)
B44 (5L470)
B45 (5L480)
B46 (5L490)
B47 (5L500)
B48 (5L510)
B50 (5L530)
B51 (5L540)
B52 (5L550)
B53 (5L560)
B54 (5L570)
B55 (5L580)
B56 (5L590)
B59 (5L620)
B60 (5L630)
B61 (5L640)
B62 (5L650)
B63 (5L660)
B64 (5L670)
B65 (5L680)
B66 (5L690)
B68 (5L710)
B70 (5L730)
B71 (5L740)
B75 (5L780)
B81 (5L840)
V-BELTS "BX" SECTION 0.66" TOP WIDTH x 0.41" THICK x 40° ANGLE
BX42
BX48
BX51
BX62
BX68
BX70
BX75
BX81

MAINTENCE SUPPLIES

AFG-1404-181BFX Silver Foil 3"x100' Indoor/Outdoor Foil Grip Tape
Foil-Grip 1404-181-BFX is a UL 181B-FX listed pressures sensitive rolled mastic sealant.
Degreaser
A heavy-duty, fast-acting, flush action aerosol that quickly cuts through and removes tough grease, oil, tar, asphalt, wax, ink, fresh paint and more! Provides high solvency and a powerful spray that blasts away grime then dries fast and residue-free.
DuroGum
DuroGum is a convenient way to seal a joint, crack or any opening so that no moisture, dust particles or air can enter the crevice.
Foam Action Coil Cleaner
A portable, non-acid, foam cleaner that blasts deep into air conditioner, heater, refrigeration, and dryer coils to loosen and remove grease, dirt, lint, and grime.
Heavy Duty Wipes
Duro Dyne Heavy Duty Wipes cut through the toughest tar, grease, wax, ink, paint, lubricants, and adhesive.
Industrial Wipes
Duro Dyne Industrial Wipes are the latest innovation in combatting paint and graffiti.
Solvent Based Coil Cleaner
A fast-drying, flush-action solvent that blasts grease, dirt, lint, and grime from air conditioner, heater, dryer, and refrigeration coils.
SureGrip 404 Indoor Application Fiber Free Solvent Base Duct Sealant
Sure-Grip 404 is a fiber-free, solvent based, synthetic rubber duct sealant.
SG 404 - 1 Gallon
SG 404 - 11oz Tubes
V-BELTS "3L" SECTION 0.38" TOP WIDTH x 0.22" THICKNESS x 40° ANGLE
3L180
V-BELTS "3VX" SECTION 0.38" TOP WIDTH x 0.31" THICK x 38° ANGLE
3VX850
3VX500
V-BELTS "A" SECTION 0.5" TOP WIDTH x 0.31" THICKNESS x 40° ANGLE
A20 (4L220)
A21 (4L230)
A22 (4L240)
A23 (4L250)
A24 (4L260)
A25 (4L270)
A26 (4L280)
A27 (4L290)
A28 (4L300)
A29 (4L310)
A31 (4L330)
A32 (4L340)
A33 (4L350)
A34 (4L360)
A35 (4L370)
A36 (4L380)
A37 (4L390)
A38 (4L400)
A39 (4L410)
A40 (4L420)
A41 (4L430)
A42 (4L440)
A43 (4L450)
A44 (4L460)
A45 (4L470)
A46 (4L480)
A47 (4L490)
A48 (4L500)
A49 (4L510)
A50 (4L520)
A51 (AL530)
A52 (4L540)
A53 (4L550)
A54 (4L560)
A55 (4L570)
A56 (4L580)
A57 (4L590)
A58 (4L600)
A60 (4L620)
A62 (4L640)
A64 (4L660)
V-BELTS "ACCU-LINK" SECTION
A-LINK-5
B-LINK-6
V-BELTS "AX" SECTION 0.5" TOP WIDTH x 0.31" THICK x 40° ANGLE
AX32
AX33
AX35
AX46
V-BELTS "B" SECTION 0.66" TOP WIDTH x 0.41" THICKNESS x 40° ANGLE
B36 (5L390)
B38 (5L410)
B40 (5L430)
B42 (5L450)
B43 (5L460)
B44 (5L470)
B45 (5L480)
B46 (5L490)
B47 (5L500)
B48 (5L510)
B50 (5L530)
B51 (5L540)
B52 (5L550)
B53 (5L560)
B54 (5L570)
B55 (5L580)
B56 (5L590)
B59 (5L620)
B60 (5L630)
B61 (5L640)
B62 (5L650)
B63 (5L660)
B64 (5L670)
B65 (5L680)
B66 (5L690)
B68 (5L710)
B70 (5L730)
B71 (5L740)
B75 (5L780)
B81 (5L840)
V-BELTS "BX" SECTION 0.66" TOP WIDTH x 0.41" THICK x 40° ANGLE
BX42
BX48
BX51
BX62
BX68
BX70
BX75
BX81
DP77 Industrial Spray Adhesive 12 oz
Features and Benefits:
  • Pressure Sensitive
  • Quick Drying
  • Permanent Bond
  • Lace-Like Web Spray Pattern
  • High Temperature Resistance - Bond Maintained After Exposure To Heat Up To 200° F
  • Non-Misting
  • No CFC’s
  • VOC Compliant
BOSS® 312 RTV HVAC/R Silicone Sealant
  • Permanently flexible
  • Adheres to glass, wood, metal, porcelain, ceramic tile, painted surfaces and rubber
  • May be applied in sub-zero weather without loss of extrusion or physical property characteristics
  • Meets NSF Standard 51 & FDA/USDA requirements for use in operations under Meat and Poultry Inspection Program
  • Insulates thermally & electrically
  • Waterproof & Weatherproof seal
  • ...
Clear
White
Aluminum
BOSS® 893 Boss Biggies Dual Side Abrasive Wipes
  • Pre-moistened
  • Textured weave for added scrubbing power
  • Contains an advanced formula and special dual-sided towel that removes:
  • Acrylic - Enamel - Epoxy - Rubber Cement - Oil - Silicone
  • Grease - Glue - Ink - Poly Foam and much more .
DP1010 WATER BASED DUCT SEALANT
  • Zero VOC
  • A premium, smooth water-based
  • UL listed, high velocity grey duct sealant for commercial and residential use
  • Qualifies for Leed™ Credit EQ 4:1
DP1010-02-01 Gallon
DP1010-02-12 Tube
DP1090 LOW VOC SOLVENT BASED DUCT SEALANT
  • Solvent Based, LEED Low VOC Duct
  • UL Classified, high velocity tan duct sealant for commercial use
  • Skins in less than a minute to help installers avoid the clean up commonly associated with solvent based duct sealers
  • Qualifies for Leed™ Credit EQ 4:1
DP1090-04-12 Tube
DP1090-04-01 Gallon
DP2502 WATER BASED DUCT LINER ADHESIVE
  • A water based, premium quality
  • UL classified duct liner adhesive
  • A higher viscosity version of DP 2501, specifically formulated for roller, brush or spray
  • Colored white
DP2502-01-54 54 Gallon White
DP2502-01-05 5 Gallon White
Stripper Cleaner & Lubricating Spray
  • An effective preventive maintenance system right at your fingertips
  • Galvanizing build-up is bad for job quality, production efficiency and profits
  • The Stripper is a degalvanizing agent that strips your machine of messy build up
  • It sprays on red for easy visibility
  • Simply Spray it on rollers of forming machines and press dies and the special ingredients get right to work and dissolve galvanized build up
  • ...